background image

EN

CHAIN SAW

USER'S MANUAL

23

 

Sharpening the saw chain

11.  SHARPENING THE SAW CHAIN

Keep the saw chain sharp. Cutting will be signifi cantly faster and most importantly safer. A blunt saw chain 
increases wear on the sprocket, guide bar, chain and engine. If you need to push on the saw and only sawdust 
with a few splinters are produced then this means that the chain is blunt.

For this task, we recommend that you contact an authorised service centre

Equipment necessary for sharpening a saw chain

  Round fi le as per technical specifi cations
 Depth 

gauge

 File 

guide

 Vice
  Medium-size fl at fi le

Sharpening the teeth on the chain

Use the fi le guide set at an angle of 30° 
(mark A, see fi gure).

  Set the saw chain tension to the correct level.
  Fasten the guide bar in a vice so that you have the 

chain in a stable position.

 

NOTE:

 

Do not fasten the chain itself.

  Push the round fi le, inserted in the fi le guide, into 

the groove between the top plate and the depth 
gauge on the chain. The chain should be touching 
both the top plate as well as the depth gauge (see 
fi gure)

 

NOTE: 

File in the middle of the guide bar.

 

NOTE: 

In the fi gure you can see the position of the fi le guide and the direction for fi ling the teeth on the left 

side of the chain.

  Place the fi le guide at the required angle (mark A, see fi gure). Check that the mark is at 30° on the fi le guide 

aligned with the centre of the guide bar. This will ensure that you will fi le at an angle of 30°.

  File the tooth in the direction from inside out (in direction B, see fi gure) until it is sharp. File only in this 

direction.

 

NOTE: 

Two to three passes of the fi le should be suffi cient to sharpen the tooth.

A

B

Summary of Contents for FZP 45016-B




































Reviews: