manualshive.com logo in svg

FIC 1stMainboard VG33, Manual, Page: 14 / 38

Share
Download
FIC 1stMainboard VG33 Manual Download Page 14

2 - 4

VG33 Mainboard Manual

1). Set System Jumper

(3). CPU Fan Installation

This connector is linked to the CPU fan. When the system is in some power saving
mode, the CPU fan will turn off; when it reverts back to full on mode, the fan will turn
back on. 

Without sufficient air circulation, the CPU may overheat resulting in

damage to both the CPU and the mainboard.
Damage may occur to the mainboard and/or the CPU fan if these pins are
used incorrectly. These are not jumpers, do not place jumper caps over these
pins.

Clear CMOS: JP3

The CMOS RAM is powered by the onboard button cell battery. To clear the
RTC data: (1) Turn off your computer (2) Place the jumper cap onto the pinpair
2-3 at least 6 seconds to enable CMOS clearance (3) Place the jumper cap onto
the pinpair 1-2 to disable the effect of CMOS clearance (4) Turn on your com-
puter until CMOS checksum error appears (5) Hold down the Delete key when
boots (6) Enter the BIOS Setup to re-enter user preferences.

Summary of Contents for 1stMainboard VG33







































Reviews:

No comments