FiberHome CiTRANS R820 Hardware Description Download Page 66

Page: 66 / 126

CiTRANS R820 Edge Router Hardware Description

Figure 5-5

Positioning of Cards in the System

5.1.5

Mapping between Cards and Slots

Table 5-3 describes the mapping between cards and slots.

Table 5-3

Mapping between Cards and Slots

Slot Type

Card

Meaning

Slot

Slot of the core

switch card

SCUS1

Router System Control Unit

SCUS2

Router System Control Unit2

SCUS3

Router System Control Unit3

Slot of the power

card

PWRS1

Power Supply Terminal Card

Slot of the service

card

MSS1

Octal Port Ethernet Mixed

Interface Card

02, 03

MSS2

Four Port Ethernet Mixed Interface

Card

MSS3

Two Port Ethernet Mixed Interface

Card

5-6

Version: A

Summary of Contents for CiTRANS R820































































































































Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands

FiberHome CiTRANS R820, Hardware Description

Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands