background image

Manual for motor FM_VM R5_R7 ( Date of publication 01/2018)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: [email protected] 
www.fialaprop.com

  

Page 3 

 

1.

 

Motor aplication 

Motors VM R5-250, VM R5-420 a VM R7-800  are  4-stroke gasoline motor with volume 250, 420 and 
800 ccm and are designed for use in model aircraft. They are not designed or recommended for any 
other use. 

2.

 

Description of the motor 

They are a 4-stroke motor with OHV and 2 valves per cylinder. Microprocessor ignition for easy 
starting and smooth running in all modes of engine speed. Dimensions and more information you can 
also see on our web  

www.fialaprop.com

 

On 

FB  Fiala Prop

 and 

You Tube channel Fiala Prop

 you can see many informations including video 

manual  how to start  4-stroke motors VM / FM, which is different from similiar 2-stroke motor 
starting. 

The 

Common instructions for the

 

 FM / VM 4-stroke engines

,  

Attachement  to manuals for radial 5-

cyl. and 7-cyl. petrol engines FM / VM,  PowerFuel RX electric fuel pump Fiala 

is

 

also annexed to 

this manual. 

3.

 

Fuel 

 

Use unleaded gasoline with a minimum octane 95 mixed 

with synthetic oil designed for two-stroke 

engines. 

For running we recommend 1:25, after running 1:30. Run-in should take about 2 hours of operation. 

We recommend Valvoline oil - SynPower 2T - Full Synthetic, Mobil 1 - Racing 2T - Full Synthetic or 
Repsol - Moto2T Racing. If you are not sure about the suitability of oil, which is going to use, contact  
authorized service center or the manufacturer directly.  

4.

 

Propeller 

For these motors we recomended following Fiala propellers:  

VM R5 - 250 –  2-blade : 32/20; 34/16; 34/18 

 

            3-blade:  30/18 

VM R5 – 420 – 2-blade: 38/24; 40/20; 42/20 

 

            3-blade:  38/20; 40/20 

VM R7 – 800 – 2-blade:  48/22 – 59/20 

                           3-blade:  45/24 - 50/20

 

Best results you get with Fiala propellers.

 

Summary of Contents for Valach Motors VM R5-250










Reviews: