manualshive.com logo in svg

FIALA MOTORS FM 60 s1-FS, Manual

Share
Download
FIALA MOTORS FM 60 s1-FS Manual Download Page 7

Manual for motor FM  60 / 70 s1-FS ( Date of publication 06/2016)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: [email protected] 
www.fialaprop.com

 

Page 7 

 

 

At the same time, or at least from time to time it is necessary to check the cleanliness of the motor, 
status / battery condition for ignition and the gap between the spark plug electrodes. This should be 
set 

to 0.4 mm

. When the electrodes are burnt, replace the spark plug. 

10.

 

Carburetor 

The standard motors mounted Walbro carburetor. Such carburettors are fitted along side by two 
adjusting rotating needles marked H (high) and L (low). Needle labeled H is used to adjust the 
carburetor / motor at maximum RPM and needle bearing L turn affects low speeds and transitions to 
the midrange. Basic settings of the two needles is 2 turns, calculated from tight needles. Fine 
adjustment and tuning of the engine should be performed by fitting the model. 

 

On this photo is also seen ventilation hose crankcase. This tubing is not clogged and leave it in its 
original length!

 

11.

 

List of common spare parts and accessories 

 Find the www.fialaprop.com, or to inform on e-mail: [email protected]

 

12.

 

Motor repair 

If, during the warranty period there is a problem or failure, please contact your dealer, who will help 
you solve the problem, or contact the manufacturer. 

We wish you a lot of satisfaction with our product! 

FIALA PROP s.r.o  
Vysoká 56  
75641 LEŠNÁ  
Czech Republic  
e-mail:    

[email protected]

 

www.fialaprop.com 

Summary of Contents for FM 60 s1-FS








Reviews:

No comments

Brands by name

Popular brands

Load more brands