manualshive.com logo in svg

FG Wilson OLYMPIAN 1001 Series, Manual

Share
Download
FG Wilson OLYMPIAN 1001 Series Manual Download Page 18

 

 

14

FAULT SYMPTOM  REMEDY 

Alam for Low Battery 
Voltage 

“LOW BATERY 
VOLTAGE” Alarm in event 
Log, Amber battery LED 
Illuminates 

1. Refer to a qualified generating set technician. 

Alarm for Not in 
Automatic Mode 
(Standby Sets Only)  

“NOT IN AUTO MODE” 
Alarm in event Log, Amber 
LED Illuminates 

1. Check module is in ‘Auto’ mode 
2. Check Emergency Stop Pushbuttons are not pressed. 
3. Check Circuit Breaker is on (handle up). 
4. Refer to a qualified generating set technician. 

Alarm for 
Approaching High 
Engine Temp 

‘APPROACHING HIGH 
COOLANT TEMP’ Alarm 
in event Log, Amber LED 
Illuminates 

1. Refer to a qualified generating set technician. 

Alarm for 
approaching low oil 
pressure 

“APPROACHING LOW 
OIL PRESSURE” Alarm in 
event Log, Amber LED 
Illuminates 

1. Refer to a qualified generating set technician. 

Alarm for Battery 
Charger Failure 

‘BATTERY CHARGER 
FAILURE’ Alarm in event 
Log, Amber LED 
Illuminates 

1. Refer to a qualified generating set technician. 

Summary of Contents for OLYMPIAN 1001 Series






























Reviews:

No comments

Brands by name

Popular brands

Load more brands