Fetco HWD-2102, User Manual, Page: 6 / 14

Go to fetco.com for the latest version of all information P119 User Guide HWD-2102 REVISED MARCH 2020 6
2
1
0
9
8
7
6 5
4
3
S3 TH
TEMPERATURE SETTING DIAL
2
1
0
9
8
7
6 5
4
3
2
1
0
9
8
7
6 5
4
3
S1 PORTION S2
PORTION CONTROL [TIMER] SETTING DIALS
TABLE OF TECHNICAL DATA
TEMPERATURE PORTION
Portion size is controlled by dispense time
Top Dial Center Dial Timer Bottom Dial Timer
SW3=Temperature SW2 Time seconds SW1=Time-10s
Celsius scale used Volume setting - 1 sec increments Volume setting - 10 sec increments
0 = 78C (172°F) 0=1second (Default to 40ml) 0=add 0 seconds
1 = 80 C (176°F) 1=1 sec. or 40ml 1=add 10 seconds
2 = 82 C (180°F) 2=2 sec. or 80ml 2=add 20 seconds
3 = 84 C (183°F) 3=3 sec. or 120ml 3=add 30 seconds
4 = 86 C (187°F) 4=4 sec. or 160ml 4 {Inactive position}
5 = 88 C (190°F) 5=5sec. or 200ml 5 {Inactive position}
6 = 90 C (194°F) 6=6 sec. or 240ml 6 {Inactive position}
7 = 92 C (198°F) 7=7 sec. or 280ml 7 {Inactive position}
8 = 94 C (201°F) 8=8 sec. or 320ml 8 {Inactive position}
9 = 96 C (205°F) 9=9 sec. or 360ml 9 {Inactive position}
Factory set at maximum—
96°C/205°F
Factory calibrated setting:
200ml/6.8oz set at 5sec at 96°C/205°F
Settings in table may vary and are given for the conditions below:
Mains 0.34MPa/50PSI and Flow Rate:5.7lpm/1½ gpm at 55°F/13°C
Correction for altitude table
Portion size setting:
Flow is 40ml per second and is proportional to mains pressure.
The two timer dials are additive and control flow for 1 to 30 seconds
Dispense volume at 1-30 seconds is approximately 40-1200ml
(1.3-40.6 fluid ounces)
Portion time =
SW1 (0, 10, 20, 30) + SW2 (0-9)
Min Time = 1 second- Will default to 40ml if SW1 & SW2 are set to 0
Max Time is 30 Seconds
Range: 1 sec to 30 seconds minimum to maximum single dispense
is 40ml/1.4 ounces to 1200ml/40.5 ounces
50psi/3.4bar/0.344MPa
Mains Pressure: 45-75 psig (0.31-0.517 mPa)
(0.34MPa/50PSI preferred
Altitude Boiling Point
(ft) (m) (
o
f) (
o
c)
-250 -76 212.5 100.3
0 0 212 100
500 152 211 99.5
1000 305 210.1 98.9
1500 457 209.1 98.4
2000 610 208.1 97.8
2500 762 207.2 97.3
3000 914 206.2 96.8
3500 1067 205.3 96.3
4000 1219 204.3 95.7
4500 1372 203.4 95.2
5000 1524 202.4 94.7
5500 1676 201.5 94.2
6000 1829 200.6 93.6
6500 1981 199.6 93.1
7000 2134 198.7 92.6
Corrections to compensate for
boiling point changes due to
elevation. Allow 5-10%
IMPORTANT When Changing Settings, after adjusting dials, or following reassembly and plugging in:
1) Switch machine “OFF” for about ten seconds
2) Toggle back “ON” (Control Reset) .