T 12+3, T 15+3, T 18+3
17
GB
8.3
Angle attachment DD-AS
[6]
The angle attachment DD-AS (in part, addi-
tional equipment) permits drilling and screw-
driving at a right angle to the machine.
8.4
Eccentric attachment DD-ES
[7]
The eccentric attachment (in part, additional
equipment) permits screwdriving near edges
with bits according to DIN 3126.
8.5
Tool holder in the drill spindle
[8]
Bits can be inserted directly in the hexagon
socket holder on the drill spindle to shorten
and reduce the weight of the machine.
9
Working with the machine
9.1
On/Off switch
[1-3]
Press = ON, release = OFF
L
The speed of the machine depends on
how far the on/off switch is pressed in.
9.2
Bit store
[1-2]
Bits or bit holders are inserted sideways into
the bit store.
9.3
Acoustic warning signal
Acoustic warning signals sound and the ma-
chine switches off in the following operating
states:
– Battery flat or machine overloaded.
X
Change the battery.
X
Place the machine under reduced stress.
– Machine is overheating.
X
You must allow the machine to cool before
using again.
– LiIon battery pack is faulty or has over-
heated.
X
Once the battery pack has cooled, per-
form a functional check using the charger.
10
Service and maintenance
Observe the following instructions:
– Keep the air slits on the machine and the
charger free and clean to ensure adequate
cooling.
– Keep the contacts on the machine, charger
and battery pack clean.
Information on battery packs
– Where possible, store the battery pack in a
cool, dry place at a temperature between
5 °C and 25 °C.
– Battery packs are most efficient at temper-
atures between 20 °C and 30 °C.
– Protect the battery pack from moisture,
water and heat.
– Significantly shorter operating times after
each charge indicate that the battery pack is
worn and should be replaced with a new one.
– The LiIon battery pack is fully compatible
with the charger! Integrated electronics
prevent overloading and overheating dur-
ing the charging process.
– Do not leave flat battery packs in a charger
disconnected from the mains power supply
for longer than one month. There is a risk
of total discharge and the maximum power
of the battery pack may decrease.
– Store the battery pack in its packaging to
reduce the risk of short circuits..
– The following applies if the battery packs are
to be taken out of service and stored for a
long period: NiMH battery packs should be
stored when fully charged; Li-ion battery
packs should be stored with a charge of 40%
(charging period approx. 15 mins.).
– NiMH battery packs that are new or have
not been used for long periods reach full
capacity after approx. five charging and
discharging cycles.
– The capacity of NiMH battery packs de-
creases drastically at ambient tempera-
tures below 0 °C or above 45 °C.
– Charge NiMH battery packs every four
months to retain maximum capacity.
– After every ten charging processes, leave
– NiMH battery packs in the charger for an
extra hour following rapid charging to com-
pensate for potential differences in capaci-
ty between the battery cells.
CAUTION
Risk of injury
X
Clamp the tool centrally in the chuck!
peep ― ―
peep peep ―
peep peep peep
Summary of Contents for T12+3
