22
HK 85 EB
GB
Release retractor lever
[4-4]
and allow the pen-
dulum guard to swivel back
[4-6]
to its final po-
sition.
Tighten screw
[4-7]
.
Reposition lever
[4-3]
.
Risk of injury!
Whenever you replace a saw
blade, always check that it is securely in
place. If a clamping flange is loose, the cut-
ting edges of the saw blade may break off, and if a
screw is loose, the saw blade may become de-
tached.
7.6
Dust extraction
Festool mobile dust extractor
A Festool mobile dust extractor with an extractor
hose diameter of 27 mm or 36 mm (36 mm is rec-
ommended due to the reduced risk of clogging) can
be connected to the extractor connector
[5-1]
at
the elbow.
– Static charge may occur if an anti-static suction
hose is not used. The user may suffer an electric
shock.
The extractor connector
[5-1]
can be rotated to
the required position when carrying out work
that does not require dust extraction.
8
Working with the electric power tool
Please observe all mentioned safety infor-
mations and the following rules when work-
ing:
– Only guide the machine against the workpiece
when it is switched on.
– Check the function of the pendulum guard prior
to use and do not use the electric power tool if it
does not slide in and out easily.
– Always secure the workpiece in such a manner
that it cannot move while being processed.
– Always hold the machine with two hands at the
handles
[1-1]
when performing work. This re-
duces the risk of injury and is a prerequisite for
precise work.
– Always push the saw forwards
[7-8]
, and never
towards yourself.
– Adapt the infeed speed to prevent the cutters on
the saw blade from overheating and prevent
plastic materials from melting during cutting.
– Make sure that the knob
[1-12]
is tightened be-
fore starting work.
– Do not use the machine when the electronics are
faulty because the machine may operate at ex-
cessive speeds. An absence of the smooth start-
up function or speed control indicates that the
electronics are faulty.
8.1
Sawing along the scribe mark
The cut indicators display the cutting sequence
without a guide rail:
0° cuts:
[6-1]
45° cuts:
[6-2]
8.2
Cutting sections
Position the saw with the front part of the saw table
on the workpiece, switch on saw and push forward
in cutting direction.
8.3
Sawing cut-outs (plunge cuts)
In order to avoid kickbacks, the following in-
structions must be observed without fail
when plunge cutting:
– Always position saw with the rear edge of the saw
table against a fixed stop.
Caution! Danger of crushing!
Always keep a firm grip on the machine with
your free hand when adjusting plunge cuts. Never
position your fingers behind or below the saw
blade.
Procedure
Adjust cutting depth,
Press lever
[7-1]
down.
Sawing unit swivels upwards to plunge position.
Hold retractor lever
[7-2]
downwards as far as
the stop.
Pendulum guard
[7-5]
opens and the saw blade
is exposed.
Position saw on workpiece and position against
a stop (kickback stop).
Switch on saw.
Slowly press down saw to the set cutting depth
until the saw engages, release retractor lever
[7-2]
and push forward in cutting direction
[7-
8]
.
WARNING
Dust hazard
Dust can be hazardous to health. Always work
with a dust extractor.
Always read applicable national regulations be-
fore extracting hazardous dust.
Summary of Contents for HK 85 EB
Page 2: ...1 1 2 1 3 1 4 1 1 1 15 1 10 1 12 1 11 1 13 1 14 1 9 1 8 1 7 1 1 1 6 1 17 1 5 1 16 ...
Page 3: ...2 3 FS 2 1 0 60 3 2 3 1 0 60 ...
Page 4: ...4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 1 4 10 4 5 ...
Page 5: ...6 7 6 1 6 2 0 45 7 4 7 3 7 5 7 8 7 6 7 7 7 2 7 1 ...
