Festool CS 70 VB, Assembly Instructions Manual

Page: 8 / 70

8
Compact CS 70 / TKS 80 EBS Accessories
1 Symbols
Warning of general danger
Read the operating instructions and
safety instructions.
Do not dispose of it with domestic
waste.
L
For the alignment and adjustment of all indi-
vidual components, we recommend using a
spirit level or an aluminium ruler (min. 1 m
long).
2 Removable leg TKS 80 EBS [1-1]
WARNING
Risk of accident from tilting power tool
f Always use the removable leg in conjunction
with the TKS 80 VB width extension table and
the TKS 80 VL length extension table.
f Make sure that the removable leg and the
foldaway legs of the TKS 80 EBS are stable.
Proceed as follows (fig. 1):
f Loosen the rotary knob screws [1-2].
f Place the removable leg [1-1] on the rotary
knob screws
[1-2]
.
f Tighten the rotary knob screws
[1-2]
.
3 Extension table
CS 70 VB / TKS 80 VB [2-3]
The extension table CS 70 VB / TKS 80 VB can be
fitted to the base table to enable exact cuts with a
stop up to a cutting width of 680 mm (CS 70 VB) /
600 mm (TKS 80 VB).
The saw table is widened by 405 mm if an extension
table is fitted on a long side of the table (usually
the right).
Proceed as follows (fig. 3):
f Unfold supports [3-7] at a 90° angle to the ta-
ble top.
f
Turn rotary knobs [3-4] fully to the left.
f Place the outer edge of the extension table on
the edge of the base table in a slightly raised
position
(fig. 3) .
f Lower extension table so that the peripheral
clamping edge
[3-1]
lies between the profile
edge [3-5] and clamping plate [3-3] .
f Insert the end of the front support [3-9] into
the slot
[3-10]
in the table frame, push down
and tighten with knurled nut [3-8] .
f Suspend rear support in slot. Push extension
table down and tighten rear knurled nut.
f
Adjust exact height. Place guide stop on base
table up to saw blade.
f Adjust height of extension table to same height
as base table with screwdriver at the adjusting
screws
[5-2] .
f Attention! Do not align with outer edge of ta-
ble since this may be 0.2-0.3 mm below the
rest of the table.
f Fit angle fence [2-1] centrally over joint be-
tween base table and extension table so that
when the fence is clamped the extension table
is aligned with the edge of the base table.
f Tighten front rotary knob
[3-4]
.
f Push extension table down on joint at rear and
tighten rear rotary knob.
f Then remove the angle fence [2-1] .
f Screw in adjusting screws [3-2] fully with
screw-driver.
f If the extension table is removed and then re-
mounted it must be pushed back against this
stop (adjusting screw). This fixation means
that it no longer has to be aligned with the an-
gle fence.
f Check that the extension table is exactly level
with the base table using the guide stop.
f The flatness of the base table can be adjusted
by adjusting the fastening
[3-6]
.
To enable the angle fence and ripping-cut fence
to be adjusted according to the existing scale, the
scale of the extension table must be fitted directly
onto the base table’s scale
(fig. 5) .
Proceed as follows:
f Release the fastening bolts
[5-1]
for the ex-
tension table’s scale.
f Slide the scale to the correct setting.
f Re-tighten fastening bolts.
English