manualshive.com logo in svg

Festo VABF-S4-1-V2B1 series, Operating Instructions Manual

Share
Download
Festo VABF-S4-1-V2B1 series Operating Instructions Manual Download Page 22

VABF-S4-1-V2B1...

22

Festo – VABF-S4-1-V2B1... – 1705c English

6.3.2

Setting the switching characteristics of the switching outputs

1. Switch on the operating voltage.

è

The vacuum block is in RUN mode (initial position).

Note

If you are not sure whether the vacuum block is in the RUN mode, hold the EDIT button

down for 3 s. The vacuum block switches into the RUN mode.

Setting the air-saving function, Out A (already preset)

To set Out A, proceed as follows:

1. Press the Edit button to access the edit mode.

è

The EDIT mode is active and [Out A] flashes.

2. Press the Edit button to confirm the selection.

3. Select the switch function [threshold value comparator] by pressing the UP/DOWN keys

(A-/B-keys).

4. Press the EDIT button to confirm the selection.

è

[SP] (switching point) flashes.

5. Adjust the switching point [SP] (e.g. -700) by pressing the UP/DOWN keys (A-/B-keys).

6. Press the EDIT button to confirm the selection.

è

[HY] (hysteresis) flashes.

7. Adjust the hysteresis [HY] (e.g. 200) by pressing the UP/DOWN keys (A-/B-keys).

8. Press the EDIT button to confirm the set value.

è

[NO] or [NC] flashes

9. Select the switching characteristic [NO] by pressing the UP/DOWN keys (A-/B-keys).

10.Press the EDIT button to confirm the selection.

è

The vacuum block is in RUN mode.

Setting the vacuum sensing, Out B (already preset)

To set Out B, proceed as follows:

1. Press the EDIT button to access the edit mode.

è

The EDIT mode is active and [Out A] flashes.

2. Press the B-key to set [Out B].

3. Select the switch function [threshold value comparator] by pressing the UP/DOWN keys

(A-/B-keys).

4. Press the EDIT button to confirm the selection.

è

[SP] (switching point) flashes.

5. Adjust the switching point [SP] (e.g. -400) by pressing the UP/DOWN keys (A-/B-keys).

è

[HY] (hysteresis) flashes.

6. Adjust the hysteresis [HY] (e.g. 5) by pressing the UP/DOWN keys (A-/B-keys).

7. Press the EDIT button to confirm the set value.

è

[NO] or [NC] flashes

8. Select the switching characteristic [NO] by pressing the UP/DOWN keys (A-/B-keys).

9. Press the EDIT button to confirm the selection.

è

The vacuum block is in RUN mode.

Summary of Contents for VABF-S4-1-V2B1 series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands