Festo CPX-E-PN, Instructions

Page: 3 / 4

[PS] (green) [PL] (green) [SF] (red) [M] (yellow)
Lights up Lights up Off Off
Tab. 8 Display Components after Error-free Commissioning
You can find information on troubleshooting in the event of incorrect behaviour in
the “Description of Automation system CPX-E” and the descriptions of the mod-
ules used
è 1.1 Applicable Documents.
10 Service
NOTICE!
Accumulation of heat due to reduced air supply to electronics.
• Keep the ventilation slots free and regularly remove contamination.
11 Diagnostics and fault clearance
11.1 Diagnostics options
Various options are available for diagnosing errors:
–
Internal system diagnostics
– LED indicators on the product
11.2 Internal System Diagnostics
• Activate internal system diagnostics via the corresponding catalogue input.
–
Status bits: E-PN [Status]
– I/O diagnostic interface: E-PN [STI]
The internal system diagnostics is described in the “Description of automation
system CPX-E”
è
1.1 Applicable Documents.
11.3 LED Displays
The network-specific LED displays are described below.
The system-specific LED indicators are described in the documents for the auto-
mation system CPX-E
è 1.1 Applicable Documents.
Network fault [NF]
LED
(red) Meaning Remedy
Network connection not OK.
Possible causes:
Device name not correct Check device name.
IO controller defective Repair IO controller.
Flashes
Network connection interrupted, short-cir-
cuited or disturbed Check network connection.
Off
No fault (if [PS] LED lights up green) –
Tab. 9 Network Fault [NF]
Maintenance/PROFIenergy [M/P]
LED
(yel-
low/gr-
een) Meaning
LED (yellow/green) Remedy
Lights up
yellow
Maintenance measures required Check push-in connector.
Flashes
green
PROFIenergy activated –
Off
No maintenance measures required, no
PROFIenergy activated –
Tab. 10 Maintenance/PROFIenergy [M/P]
Connection status [XF1], [XF2]
LED
(green) Meaning Remedy
Lights up
Network connection OK –
Flashes
Locating module if the LEDs XF1 and XF2
flash synchronously;
e.g. for fault finding or during configura-
tion –
Off
No network connection Check network connection.
Tab. 11 Connection Status [XF1], [XF2]
12 Disposal
ENVIRONMENT!
Send the packaging and product for environmentally sound recycling in accord-
ance with the current regulations
è www.festo.com/sp.
13 Technical Data
13.1 General Technical Data
General technical data
General technical data
Automation system CPX-E Description of automation system CPX-E
è 1.1 Applicable Documents
Dimensions
(length × width × height)
1)
[mm] 125.8 × 37.8 × 76.5
Product weight
2)
[g] 145
Mounting position Vertical/horizontal
Ambient temperature with
vertical mounting position [°C] –5 … +60
3)
Ambient temperature with
horizontal mounting position [°C] –5 … +50
3)
Storage temperature [°C] –20 … +70
Humidity (non-condensing) [%] 0 … 95
Module code/sub-module code
(CPX-E-specific) 222/34
Module identification E-PN
Degree of protection in accordance with
EN 60529 IP20
The degree of protection is not UL-tested.
Protection against electric shock
(Protection against direct and indirect
contact in accordance with IEC 60204-1) through the use of PELV circuits
(protected extra-low voltage)
Electromagnetic compatibility To EN 61000-6-2/-4 and NE 21
Assigned address space (inputs/outputs)
Without diagnostics [bit] –/–
With status bits [bit] 8/–
With I/O diagnostics inter-
face [bit] 16/16
1) not including linking element
2) Including linking element
3) for non-conforming technical data see UL operating conditions table UL
Tab. 12 General Technical Data
Power supply
Operating power supply
U
EL/SEN
[V DC] 24 _ 25%
Intrinsic current consumption
at nominal operating voltage
24 V from U
EL/SEN
[mA] 73
Reverse polarity protection
24 V U
EL/SEN
against 0 V
U
EL/SEN
Yes
Mains buffering time [ms] 20
Tab. 13 Power Supply
Network-specific data
Protocol PROFINET
1)
Specification
(Standards and norms with reference to
PROFINET) IEC 61158
IEC 61784
IEC 61918
Conformity class CC-C
Transmission rate [Mbps] 100
Crossover detection Auto-MDI/MDI-X