Translation of the original instructions
1
About this document
This document describes the use of the above-mentioned product.
Certain aspects of use are described in other documents and must be observed
è
1.1 Further applicable documents.
1.1
Further applicable documents
Document
Table of contents
Description of automation system CPX-E
(CPX-E-SYS)
Detailed description of automation system CPX-E
Instruction manual for use of automation system
CPX-E (CPX-E-SYS)
Instruction manual and important information on
assembly, electrical installation and mainten-
ance tasks for an automation system CPX-E
Description of counter module CPX-E-1CI
(CPX-E-1CI)
Detailed description of product function and
parameterisation options
Documentation of the components in an automa-
tion system CPX-E and the connected peripherals
Information on using the components
Documentation for the higher-order controller
and the additional participants in the network
Information on commissioning and paramet-
erisation of the components
Tab. 1 Further applicable documents
All available documents for the product
è
www.festo.com/pk.
1.2
Product version
This document refers to the following product versions:
Product
Version
CPX-E-1CI
Counter module CPX-E-1CI, revision 1 or later
Tab. 2 Product version
The product version can be identified from the product labelling or with the help
of appropriate software from Festo.
Appropriate software for determining the product version can be found in the
Festo Support Portal
è
Information on using the software can be found in the integrated Help function.
There may be an updated version of this document for these or later product ver-
sions.
•
Check whether a corresponding version of this document is available on the
Festo Support Portal
è
1.3
Product labelling
The product labelling is located on the left-hand side of the module. Scanning the
printed Data Matrix Code with an appropriate device opens the Festo Support
Portal, with the information appropriate for the product. Alternatively, the Product
Key (11-digit alphanumeric code on the product labelling) can be entered in the
search field of the Support Portal.
You can find detailed information on the product labelling in the description of the
module
è
1.1 Further applicable documents.
1.4
Specified standards
Version status
EN 60529:2013-10
IEC 60204-1:2014-10
EN 61000-6-2:2005-08
IEC 61131-2:2015-05
EN 61000-6-4:2007-01
–
Tab. 3 Standards specified in the document
2
Safety
2.1
Safety instructions
–
Take into consideration the legal regulations for the respective destination.
–
Use the product only within the defined values
è
–
Observe labelling on the product.
–
Observe further applicable documents.
–
Store the product in a cool, dry, UV-protected and corrosion-protected envir-
onment. Ensure that storage times are kept to a minimum.
–
Before working on the product: switch off the power supply and secure it
against being switched on again.
–
Comply with the handling specifications for electrostatically sensitive devices.
2.2
Intended use
The product described in this document is intended only for use in automation
systems CPX-E.
Use the product only as follows:
–
Use only in an industrial environment. Outside of industrial environments,
e.g. in commercial and mixed-residential areas, it may be necessary to take
measures to suppress interference.
–
Use only in combination with modules and components that are permissible
for the respective product variant
è
www.festo.com/catalogue.
–
Only use the product if it is in perfect technical condition.
–
Only use the product in original status without unauthorised modifications.
Only the conversions or modifications described in this and the further applic-
able documents are permitted.
2.3
Training of skilled personnel
Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel.
The qualified personnel must be familiar with installation of electrical control sys-
tems.
3
Additional information
–
Accessories
è
www.festo.com/catalogue.
–
Spare parts
è
www.festo.com/spareparts.
4
Service
Contact your regional Festo contact person if you have technical questions
è
www.festo.com.
5
Product overview
5.1
Function
In an automation system CPX-E, the module offers the option of connecting an
encoder for detecting pulses. The encoder supply has an electronic fuse for pro-
tection against short circuit or overload. After the elimination of a short circuit or
overload, the encoder supply is switched on again automatically.
The module provides the following functions:
–
Setting the counter
–
Blocking the counter
–
Latching
–
Speed measurement
The module also provides 4 digital inputs (I0 ... I3), each of which can be used to
trigger a particular function:
–
Input I0: trigger latching
–
Input I1: block latching
–
Input I2: set counter
–
Input I3: block counter
The debounce time of inputs I0 ... I3 and the module response can be set using
module parameters.
The following encoder types can be used with the module:
–
Encoder 24 V DC (single ended)
–
Encoder 5 V DC (differential or single ended)
You can find detailed information on the types of encoder that can be used in the
description of the module
è
1.1 Further applicable documents.
8071179
Counter module
CPX-E-1CI
8071179
2018-02
[8071181]
Instructions |Use
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
