background image

8

Festo — CPX-AP-A-8DI-M12-5P — 2022-07

Diagnostics and fault clearance

Response of the display components of the module after error-free commissioning

[MD]

green light

Tab. 6: Response of the LED displays of the module after error-free commissioning

Information on troubleshooting in the event of incorrect response:

è

 9 Diagnostics and fault clearance

è

 1.1 Applicable documents

8

Parameterisation

Various parameters are available for reading out information about the modules in an automation
system CPX-AP-A and for adapting the modules to the application situation.
Write access to the parameters is typically performed by the higher-level controller using the device
descriptions specific to the host system.

ID

Parameter

Instances Data type

Access

1

)

Array
size

246

Fieldbus serial number

1

UINT32

ro

791

Product key

1

CHAR

ro

12

960

Firmware version

1

CHAR

ro

30

20000

Module code

1

UINT32

ro

20014

Input debounce time

0: 0.1 ms

1: 3.0 ms (factory setting)

2: 10 ms

3: 20 ms

1

ENUM_ID

rw

20085

Measured value of temperature AP-ASIC [°C] 1

INT16

ro

20087

Current measured value of logic supply (PS) 1

UINT16

ro

20088

Current measured value of load supply (PL)

1

UINT16

ro

20093

Hardware version

1

UINT8

ro

1) ro = read only; rw = read write

Tab. 7: Parameter

9

Diagnostics and fault clearance

9.1

Diagnostics messages

The following table contains the diagnostic messages of the module.

Summary of Contents for CPX-AP-A-8DI-M12-5P

















Reviews: