background image

7

Safety

Operator Safety

23. Use care when approaching blind corners, shrubs,

trees or other objects that may obscure vision.

24. To reduce fire hazard, keep unit free of grass,

leaves & excess oil. Do not stop or park over dry
leaves, grass or combustible materials.

25. The engine in this unit is not factory equipped with

a spark arrester. It is a violation of California
Public Resource Code Section 4442 to use or
operate the engine on or near any forest-covered,
brush-covered, or grass-covered land unless the
exhaust system is equipped with a spark arrester
meeting any applicable local or state laws. Other
states or federal area may have similar laws.

26. OSHA regulations may require the use of hearing

protection when exposed to sound levels greater
than 85 dBA for an 8 hour time period.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not
drive on it.

Do

1. Mow across slopes, not up and down.
2. Remove obstacles such as rocks, tree limbs, etc.
3. Watch for holes, ruts, or bumps. Uneven terrain

could overturn the unit. Tall grass can hide
obstacles.

4. Use slow speed. Choose a slow speed so that

you will not have to stop or change speed while
on the slope.

5. Use extra care with grass catchers or other

attachments. These can change the stability of
the unit.

6. Keep all movement on the slopes slow and

gradual. Do not make sudden changes in speed
or direction.

7. See your authorized dealer for recommendations

of available weights to improve stability.

Do Not

1. Avoid starting, stopping, or turning on a slope. If

tires lose traction (i.e. machine stops forward
motion on a slope), disengage the blade(s) (PTO)
and drive slow off the slope.

2. Do not turn on slopes unless necessary, and then,

turn slowly and gradually uphill, if possible. Never
mow down slopes.

3. Do not mow near drop-offs, ditches, or

embankments. The operator could lose footing or
balance or mower could suddenly turn over if a
wheel is over the edge of a cliff or ditch, or if an
edge caves in.

4. Do not mow on wet grass. Reduced footing or

traction could cause sliding.

5. Do not try to stabilize the unit by putting your foot

on the ground. (ride-on units)

6. Do not mow excessively steep slopes.
7. Do not use grass catcher on steep slopes.
8. Do not mow slopes if you cannot back up them.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed

for towing. Do not attach towed equipment except
at the hitch point.

2. Follow the manufacturer’s recommendations for

weight limit for towed equipment and towing on
slopes. See attaching a trailer under OPERATION.

3. Never allow children or others in or on towed

equipment.

4. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.
6. Do not shift to neutral and coast down hill.

CHILDREN

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the unit and the mowing activity. Never assume that
children will remain where you last saw them.

1. Keep children out of the mowing area and under

the watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.
3. Before and during reverse operation, look behind

and down for small children.

4. Never carry children, even with the blade(s) off.

They may fall off and be seriously injured or
interfere with safe unit operation. Children who
have been given rides in the past may suddenly
appear in the mowing area for another ride and be
run over or backed over by the machine.

5. Never allow children to operate the unit.
6. Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure
vision.

EMISSIONS

1. Engine exhaust from this product contains

chemicals known, in certain quantities, to cause
cancer, birth defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period

and Air Index information on the engine emissions
label.

CAUTION

This machine produces sound levels
in excess of 85 dBA at the operator’s
ear and can cause hearing loss
though extended periods of exposure.

Wear hearing protection when operating this
machine.

WARNING

Do not use this machine on slopes greater than
15°.* 

Select slow ground speed before driving onto
slope. Use extra caution when operating on
slopes with rear-mounted grass catchers.

Mow across the face of slopes, not up and
down, use caution when changing directions
and DO NOT START OR STOP ON SLOPE.

*This limit was determined per CEN Standard EN 836:1997, Section
5.2.2 and is based on the EN 836 Stability Test procedure described in
Section 4.2.4.2. The 15 degree “limit of stability” is equal to 50% of the
angle at which machine lift-off occurred in static tests. Actual dynamic
stability may vary depending on operating conditions.

Summary of Contents for 5900751



















































Reviews: