MAINTENCE, CARE AND REPAIR
Switch off and unplug the machine before carrying
out any cleaning or maintenance work.
CLEANING
Wear personal protection equipment during cleaning.
Do not use water or flammable liquids to clean the san-
der, clean with a soft brush.
FAULTS
Switch OFF immediately at the mains plug and
remove the plug when:
•
The plug or cable is damaged.
•
The switch on the machine is defective.
•
You smell or see smoke caused by scorched insula-
tion in the machine
Overheating
•
Put less pressure on the workpiece
•
The dust is not removed.
Check holes in sander sole are clear and line up with
holes in the abrasive sheet.
Clean the dust extraction opening.
Empty the dust extractor bag.
The machine does not start when switched on
•
Check the mains lead and the fuse/plug.
Take to your Ferm Dealer for repair
The motor is defective
•
T ake to your Ferm Dealer
There are no user serviceable/repairable parts inside this
machine. Qualified service engineers must carry out
repairs and servicing.
MAINTAIN TOOLS WITH CARE
Keep the tool clean for better and safer performance.
Follow instructions for changing accessories. Inspect
tool and extension cables periodically and if damaged,
have them repaired by a qualified person or authorised
service body.
Check for damaged parts
Do not use a tool with damaged parts, before further use
a damaged tool must be carefully checked by a qualified
person to determine that it will operate properly. Check
for alignment of moving parts, binding or breakage of
parts, mounting and other conditions that may affect its
operation.
A damaged part or guard should be properly repaired by
an authorised service centre, unless indicated otherwise
in the instruction manual. Have defective switches
replaced by an authorised service centre. Do not use a
tool if the switch does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
ELECTRICAL INFORMATION
This product is complete with a pre-wired mains plug, If
the plug needs replacing follow these instructions.
Wire correctly
The wires in the mains lead are coloured in the following
way:
BLUE
•
Neutral
BROWN
•
Live
YELLOW/GREEN
•
Earth
Securing wires
Secure wires carefully and firmly to the correct termi-
nals. Secure the mains cable in the plug cord grip firmly
Fit a 5-amp fuse. If a 13amp (BS1363) plug is used a (BS
1362) ASTA approved 5-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of
electric shock.
ENVIRONMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please
recycle where facilities exist. Phone the Helpline for cur-
rent advice on recycling.
Helpline
For any questions relating to operational or safety
matters contact:
Ferm Customer Helpline on:
0115 966 1199
Monday-Friday
8am - 6pm
Saturday
9am - 1 pm
Blue
(Neutral)
Green & Yellow
(Earth)
Brown
(Live)
Fuse
(5 Amp)
Ferm
5
USING THE ORBITAL SANDER
The sander is designed for sanding wood, removing
rust, sanding metal and polishing only.
This machine is designed to be used hand held - do not fix to a
bench with clamps or vice.
Ensure the sander is switched off and unplugged.
BEFORE OPERATING
•
Check the voltage on the sander corresponds with
your power supply voltage and that the plug and lead
are in good condition.
•
You have the correct type of abrasive. Depending on
the finish required use coarse grade 50 for
rough/uneven surfaces and medium grade 80 for
more even surfaces, finally finish with fine grade 120.
•
The sander is only for use on dry surfaces. It is not
designed to be used in wet or damp conditions. Do
not use water as a lubricant/cutting medium or wet
and dry abrasive paper
•
Use abrasive sheets designed for the sander
only.They have dust extraction holes to remove
debris from the surface and will last longer.
•
Ensure you have and wear suitable personal protec-
tion equipment during sanding and cleaning.
•
Route the mains lead away from work area.
•
Run idle for 30 seconds - if there is any abnormal vib-
ration or other fault. Switch off, inspect and rectify
before continuing
FITTING THE DUST COLLECTOR BAG
Ensure the sander is switched off and unplugged.
Refer to illustration below.
•
The dust bag attaches to the opening at the side of the
machine.
•
Push the fitting onto the dust exhaust hole (2). Line
up arrow on the bag fitting with parallel marks on the
sander.
•
Twist 90 degrees to lock.
•
During use empty bag frequently.
FITTING THE ABRASIVE SHEETS
Ensure the sander is switched off and unplugged.
Refer to illustration below.
•
The sole of the sander is designed to extract dust.
Only use abrasive sheets with holes that are suitable
for the sander.
•
Open the rear clamp. Lift up lever (3).
•
Position the abrasive sheet on the sander sole (4)
making sure that the holes in the sheet line up with
the holes in the sole.
•
Close the rear clamp.
•
Open the front clamp and position the abrasive paper
as tight as possible, making sure the holes line up.
•
Close the front clamp.
OPERATION
Make sure the sander is switched off.
Plug into a suitable mains supply. Check the cable is routed
well away from moving parts and switch on at plug.
To switch the sander ON
Press the trigger switch (1).
Continuous operation
Press button in while trigger switch is depressed then
release trigger switch. The machine is now in continuous
operation mode.
To switch OFF
Release trigger switch (depress and release in conti-
nuous operation mode).
To vary speed
Rotate wheel (8) to obtain the best speed for the job (1 is
slow, 6 is fast).
DURING USE
•
Use gentle pressure. Excessive pressure will clog the
abrasive paper and slow the sanding action.
•
Regularly inspect the abrasive during use (switch off
first) for signs of damage or wear and replace as
required.
•
Keep the machine moving. This allows the debris to
be cleared easily and increases the life of the abrasive.
•
Keep the ventilation slots clear. Clean dust and
debris with soft brush (switch off and unplug first).
•
Dust collection. Always use the dust collection items
supplied, they do not provide complete protection
from very fine dust, therefore it is strongly recom-
mended that a suitable dust mask should be worn in
addition to other personal protection items.
1
2
3
4
5
6
7
8
4
Ferm
