background image

45134        03/2017

7  VARIABLE SPEED POLISHER

CALIFORNIA PROPOSITION 65

WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer,
birth defects, or other reproductive
harm. Wear protective gear.

WARNING: This product or its
power cord may contain
chemicals, including lead, known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
after handling.

Important!

When using equipment, a few safety

precautions must be observed to

avoid injuries and damage. Please

read the complete operating manual

with due care. Keep this manual in a

safe place, so that the information is

available at all times. If you give the

equipment to any other person, give

them these operating instructions as

well. We accept no liability for

damage or accidents which arise due

to non-observance of these

instructions and the safety information

herein.

SPECIFICATIONS
Motor: 

120V ~ 60Hz, 9.2 Amp

No-Load Speed: 

200 - 3,350 RPM

Buffing Diameter: 

7

Keep this manual and receipt in
a safe and dry place for future
reference.

GENERAL SAFETY RULES

WORK AREA

 KEEP THE WORK AREA CLEAN

AND WELL LIT. Cluttered benches

and dark areas increases the risk

of injury.

 DO NOT OPERATE THE TOOL

IN EXPLOSIVE ATMOSPHERES,

such as in the presence of

flammable liquids, gases, or dust.

The tool may create a spark that

could ignite flammable liquids,

gases, or dust.

 KEEP VISITORS AWAY. Do not

let visitors handle the tool. All

visitors should be kept safely

away from the work area.

 NEVER ENGAGE IN

HORSEPLAY WITH THE TOOL.

Respect the tool as a working

implement.

PERSONAL SAFETY

 OPERATORS AND OTHERS IN

WORK AREA MUST WEAR

SAFETY GLASSES WITH SIDE

SHIELDS. Safety glasses must

conform to ANSI Z87.1

specifications.

Models: 45134

For Customer Service, please call 

1-800-348-5004

 or 

email 

[email protected]

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this
product. Observe all safety information to protect yourself and others. Failure to observe the instructions may
result in property damage and/or personal injury. Please keep instructions for future reference.

Important Operating Instructions

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

1

Summary of Contents for 45134












Reviews: