Afiação das lâminas (Nível 3))
Fig. 28 - 33
Ferramentas necessárias:
2
chave inglesa S8-S10
1
lima plana
1
chave de fendas
Peças necessárias:
4
porcas de bloqueio
Aviso! As lâminas do aparador de sebes são muito afiadas. Use luvas para proteger as mãos.
•
Desligue o arame da vela de ignição.
•
Retire o esticador da lâmina
•
Retire os dois parafusos (J) na parte inferior da protecção da pega frontal.
•
Retire os três parafusos (K) na placa de suporte da lâmina.
•
Retire as porcas de bloqueio do esticador da lâmina (L) e as anilhas. Não retire os parafusos da lâmina.
•
Retire o esticador da lâmina.
•
Aperte novamente as porcas de fixação (L) e as anilhas na lâmina
•
Faça deslizar as lâminas para permitir a utilização da lima através das ranhuras (M) na parte inferior da lâmina. Não force o aparador
contra extremidades cortantes.
•
Afie cada extremidade com cuidado. Siga o formato original da lâmina.
Importante:
se utilizar um esmeril, não deixe que a lâmina aqueça demasiado.
•
Monte o esticador da lâmina pela ordem inversa.
Nota:
utilize novas porcas de bloqueio sempre que montar o esticador da lâmina.
•
Lubrifique as lâminas (consulte as instruções de lubrificação).
Importante:
as lâminas só devem ser retiradas e montadas novamente por um serviço de assistência autorizado, caso contrário pode
ocorrer um desgaste prematuro ou danos internos.
Ferm
81
GB
D
NL
F
E
P
PETROL HEDGE TRIMMER 26CC
The numbers in the following text correspond with the figures on page 2-9.
Please read and make sure that you understand this manual before operation. Keep it in a safe place for future reference. It
contains specifications and information for operation, starting, stopping, maintenance, storage, and assembly specific to this
product.
Please read and make sure that you understand the safety instructions before operation. Keep it in a safe place for future
reference. It explains possible hazards involved with the use of this product and which measures you should take to make using
this product safer.
Introduction
This product was designed and manufactured to provide long life and on-the-job dependability. Please read and make sure that you
understand this manual. You will find it easy to use and full of helpful operating tips and safety messages. Specifications, descriptions and
illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations
may include optional equipment and accessories, and may not include all standard equipment.
Contents
1.
Machine data
2.
Safety
3.
Operation
4.
Maintenance
1. MACHINE DATA
Technical specifications
* Do not use fuel containing methyl alcohol, more than10% ethyl alcohol or 15% MTBE.
Package contents
After opening the carton, check for damage. Immediately notify your retailer or the address on the warranty card of any damaged or missing
parts. Use the contents list to check for missing parts:
1 Hedge trimmer
1 T-Wrench 17 x 19
1 Spanner S8-S10
1 Fuel-oil mixing bottle
1 Instruction manual
1 Safety instructions
1 Warranty card
Engine type
Air cooled, 2-stroke, single cylinder, petrol engine
Engine power
0.75 kW
Idle speed
2800 - 3200/min
Displacement
26 cc
Bore
34.0 mm (1.34”)
Stroke
28.0 mm (1.10”)
Exhaust system
Muffler
Carburettor
Ruixing
Ignition system
Flywheel magneto, capacitor discharge ignition
Spark plug
BPMR7A(Gap 0.65 mm (0”.026)
Fuel
Mixed fuel, petrol and oil, 25:1
Petrol
89 Octane unleaded *
Oil
Universal 2-stroke engine oil
Fuel tank capacity
0.6 L (20.3 fl. oz)
Starter system
Automatic recoil starter
Clutch
Centrifugal type
Gear case ratio
58:14
Cutter
Double reciprocating blade, double edge
Blade length
600 mm (24”)
Teeth pitch
27 mm (1.06”)
Max. cutting diameter
10 mm (0.4”) (soft wood)
Dry weight
5.8 kg (12.3 lb.)
Vibration front handle
15.08 m/s
2
Vibration rear handle
17.75 m/s
2
Lpa (sound pressure)
95 dB (A)
Lwa (sound power)
107 dB (A)
08
Ferm
GB
D
NL
F
E
P