SPARE PARTS
REF.NR.
DESCRIPTION
FERM NR.
1
STATOR
406765
2
BEARING
406715
6
CARBON BRUSH SET (2 PIECES)
406396
7
ROTOR
406764
8 + 21
ENCLOSURE COMPLETE
406358
9 + 10
B HOLDER
406364
12
BALL BEARING 6001 ZZ
806001
13
PVC FOOT
406151
14
PAPER CLAMP
406782
16
SANDING PAD
406763
20
SWITCH
406362
Ferm
9
EXPLODED VIEW
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
•
Excessive sparking of the carbon brushes and
verticiliosis in the collector.
•
Interruption in the mains plug, mains lead or mains
lead damage.
•
Defect switch.
•
Smoke or stench of scorched isolation.
TECHNICAL SPECIFICATIONS
Electrical safety
Always check that the power supply corres-
ponds to the voltage on the rating plate.
Your machine is double insulated in
accordance with EN 50144; therefore no
earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm2. When using a cable reel always unwind
the reel completely.
PRODUCT INFORMATION
Fig. A.
1. On/off switch
2. Dust collection opening
3. Dust exhauster adaptor
4. Paper clamp
5. Sand sole
6. Handle (behind)
7. Blocking switch
8. Handle (front)
OPERATION
Fig. B.
Choice of the sand-paper.
Coarse sand-paper (grain 50) removes in general the
bigger part of the material and fine sand-paper is used for
the finishing. If the surface is not even, then start with
rough sand-paper. Further you use middlecoarse sand-
paper (grain 80) to remove the scratches left behind by
the coarse sand-paper and finally you take fine sand-
paper (grain 120) for the finishing.
Installing sand-paper.
The sanding machine is provided with a rectangle sand
sole. By tightening the sand-paper it does not wear out
that fast and so it will wear well longer.
•
Pull the mains plug out of the power-point;
•
Open the hindmost clamp by pressing up the
interlocking;
•
Install the sand-paper under the clamp, see to the
paper being in the middle and look after the
perforations in the paper. They have to correspond
with those on the sand sole, so that the dust can be
exhausted.
•
Put the clamping spring back into the original
position.
•
Repeat the operation to fix the sand-paper on the
front side.
•
Check all the time if the exhaust gaps are not stopped
up when you place the sand-paper, and check if the
perforations in the sand-paper correspond with the
exhaust gaps.
•
Fix the sand-paper as tight as possible.
Before assembly sanding paper always remove
the plug from the mains.
DUST COLLECTION FEATURE
Fig. C.
For a better dust extraction of the working surface your
sanding machine can be connected to the ordinary
vacuum cleaner for house-use. You can use the adaptor
(see figure). The adaptor has to be installed on the back
side of the machine, in the opening.
OPERATION
-
Push the ON/OFF-switch to make your sanding
machine work.
-
If you want to disconnect the machine, you have to
let loose the same ON/OFFswitch. The ON/OFF-
switch can be blocked in position “ON” by pushing
the switch on the side, while you keep pushing the
ON/OFF-switch. The machine can be disconnected
by briefly pushing the ON/OFF-switch.
APPLICATIONS
(Only useful for subjoined applications)
1. Sanding wooden surfaces.
2. Removing rust and sanding metal surfaces.
3. Polishing.
GRIPS
The use of your sanding machine is made easier because
of the two grips one on the front side and one on the
back side. Through that you can hold the machine with
two hands, so that you have a better control of the
machine and besides you do not risk becoming in touch
with the moving parts. Hold your sanding machine
always with your both hands.
Voltage
Frequency
Power input
No load speed
Sand paper dimensions
Weight
Lpa (sound pressure)
Lwa (sound powerlevel)
Vibration value
230 V~
50 Hz
135 W
11000/min.
187 x 90 mm
1,2 kg
84,24 dB(A)
97,24 dB(A)
2,5 m/s2
4
Ferm
