background image

This literature is provided for informational purposes only.  
KIDDE-FENWAL, INC. assumes no responsibility for the prod-
uct’s suitability for a particular application. The product must be 
properly applied to work correctly. If you need more informa-
tion on this product, or if you have a particular problem or 
question, contact KIDDE-FENWAL, INC., Ashland, MA 01721.

© 2015    Kidde-Fenwal Inc.     P/N F-35-63     Rev AA

Fenwal Controls, Kidde-Fenwal Inc.
400 Main Street
Ashland,  MA 01721
Tel: 800-FENWAL-1
Fax: 508-881-7619
 www.fenwal.com

FENWAL

®

 and DETECT-A-FLAME

®

 are registered trademarks of Kidde-Fenwal Inc. 

All other trademarks are the property of their respective owners.

PART NUMBER CONFIGURATION

35 - 63  0  X X X - X X X

Trial for Ignition Time

1 = 15 econds
3 = 30 econds
5 = 60 econds
7 = 90 econds

S
S
S
S

Inter-Purge Time

0 = None (Single Try Models Only)
1 = 15 econds
2 = 30 econds
3 = 45 Seconds
4 = 4 Minutes

S
S

Product
Designation

*

*

1 = Recycle After Loss of Flame
2 = Standard CE Approved Model
3 = Special CE Approved Model
5 = Re-ignition After Loss of Flame
9 = Special Configuration

Pre-Purge Time

0 = None
1 = 15 Seconds
2 = 30 Seconds
3 = 45 Seconds
4 = 4 Minutes

Number of Ignition Trials, Flame Sense Method and
Lockout Reset Method

0 = Single Try, Local Sense
1 = Single Try, Remote Sense
2 = Single Try, Local Sense
3 = Single Try, Remote Sense
5 = Three Tries, Local Sense
6 = Three Tries, Remote Sense
7 = Three Tries, Local Sense
8 = Three Tries, Remote Sense

Enclosure Configurations

0 = Noryl Gray Enclosure
1 = Integral Standoffs
2 = Board Only

*

On CE Approved models,

pre-purge time cannot exceed
inter-purge time and automatic
reset is not permitted.

Thermostat/power off reset
Thermostat/power off reset
1 Hour Automatic reset
1 Hour Automatic reset
Thermostat/power off reset
Thermostat power off reset
1 Hour Automatic reset
1 Hour Automatic reset

A 3 or 9 in this location
(i.e. 35-63 0 901 -113)
indicates a special configuration.
9XX is a sequentially assigned
part number and does not follow
the standard part numbering
configuration.

Consult Fenwal for operating
characteristics of this control.

SERIES

Summary of Contents for 35-63







Reviews: