Fenwal Controls 35-9 Series Operation And Installation Instructions Manual Download Page 12

Fenwal Controls, Kidde-Fenwal Inc.

400 Main Street

Ashland, MA 01721

Tel: 800-FENWAL-1

Fax: 508-881-7619

 

www.fenwal.com

tekmar is a registered trademark of tekmar Control Systems Ltd. and tekmar Control Systems, Inc.
PIM is a registered  trademark of Kidde-Fenwal Inc. All other trademarks are the property of their respective owners.

This literature is provided for informational purposes only. KIDDE-FENWAL, INC. believes this data to be accurate, but it is published and presented without any guarantee 
or warranty whatsoever. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The product must be properly applied to 
work correctly. If you need more information on this product, or if you have a particular problem or question, contact KIDDE-FENWAL, INC., Ashland, MA 01721 USA. 
Telephone: (508) 881-2000.

F-35-2000 Rev AB

©2018 Kidde-Fenwal, Inc.

12 of 12

PIM PART NUMBER

The following image explains the meaning of the various digits in the part number. Use this information to order the correct board.

35 – 9 X X X X X  X X X 

IGNITION TYPE
1 = Direct Spark
2 = Direct Spark with External Relay
6 = Hot Surface Ignition
7 = Proven Hot Surface Ignition

VALVE/FAN CONFIGURATION
0 = Modulating (1-stage)
1 = One Stage
2 = Two Stage
3 = Intermittent Pilot (PV/MV)
4 = One Stage with Auxiliary
5 = Isolated Modulating (1-stage)
6 = Isolated One Stage
7 = Isolated Two Stage

RESERVED
0 = Standard Model
0-9 = Special Feature Assignment

TERMINAL CONFIGURATION
0 = Standard
1 = Pluggable Field Terminal Blocks

BLOWER RELAY
0 = Standard (5A)
1 = High-Current (15A)

FLAME SENSE METHOD
0 = Local Sense
1 = Remote Sense
3 = Dual (Local and Remote)

RESERVED
0 = Standard Model
0-9 = Special Feature Assignment

MODEL CONFIGURATION
0 = North American (C22.2-199) Standard Model
2 = CE (EN298 & 60730) Standard Model
3 = CE (EN298 & 60730) OEM Special Feature Model
5 = North American (60730) Standard Model
6 = North American (60730) OEM Special Feature Model
9 =North American (C22.2-199) OEM Special Feature Model

Description

EXPORT INFORMATION (USA)

Jurisdiction: EAR

Classification: EAR99

This document contains technical data subject to the EAR.

Summary of Contents for 35-9 Series














Reviews: