background image

 

SUPER CHAMP

®

 XD

 

(This is the model name for warranty claims) 

 

5

 
 

PCB EXCHANGE POLICY 

 
Parts marked with a single asterisk (

*

) in the Part 

Lists are not field replaceable.  If a failure due to 
one of these components is detected, please con-

tact the FMIC Customer Service Department to 
order the complete PCB Assembly. 

CIRCUIT DESCRIPTION 

 
This section provides concise information about new 
or unusual circuitry designs incorporated into this 
amplifier model.  The purpose is to aid the service 
technician by providing insight into the design areas 
most likely to become obstacles in troubleshooting.  
Information is focused for its effective use while 
maintaining the security of Fender® proprietary in-
formation wherever possible. 

MAIN PCB 

The main PCB contains the circuitry for the pre-
amplifier, the power amplifier and the power supply. 
The controls are located on a breakaway section of 
the main PCB with ribbon cables connecting them. 

PRE-AMPLIFIER  

Op-amp U7-A provides the high impedance instru-
ment input with 15db of gain.  Op-amp U7-B is 
configured as a three pole active filter.  The filtered 
output signal (Lin) drives the encoder portion of the 
CODEC U13 of the uDSP PCB.  Signal VQ2 is the 
D.C. reference voltage from the CODEC thus center-
ing the output signal about this level.    Op-amp U3-A 
is configured as a differential input amp recovering 
the signal after uDSP processing and conversion 
back to an analog signal in the decoder portion of the 
CODEC U13. The LOUT+ and LOUT- signals are the 
input to the differential amp which acts as a three 
pole active low pass filter. The output of U3-A is ap-
plied to a  buffer amp U1-A which drives op-amp U1-
B which provides the LINE OUT signal and the 
power amp input. FET Q1 provides system muting 
during power up/down in conjunction with the power 
sense circuits comprised of D9, Q2 and Q4. 

 

USER INTERFACE 

The 4 - 16 position encoders (S2 –S3) for the VOICE 
and EFFECT SELECT are read via the port ex-
pander U4 and the data sent to the uDSP system via 
the I

2

C interface lines SCL and SDA.  

 
The 6 potentiometers CH1 VOLUME (R85), CH2 
VOLUME (R83), CH2 GAIN (R84), TREBLE (R82), 
BASS (R81) and FX LEVEL (R80) generate DC volt-
ages (+1.0V to +4.0V) that are read by the analog 
multiplexer U6. IO0-IO3 are the digital control lines 
used to multiplex these analog signals which are 
sent serially to the system CODEC U13 on the Rin 
channel.   The uDSP system reads the state of these 
controls and inputs digitally from the CODEC.  
 

POWER AMPLIFIER  

The power amplifier consists of V1, V2, V3, T2 and 
associated circuitry. The signal is fed to the gate of 
V1-B in common cathode configuration. The signal 
is then fed from the plate of V1-B to the gate of V1-
A which is operating as a phase splitter which 
drives V2 from its plate and V3 from its cathode. V2 
and V3 are operating in class A-B push-pull mode. 
T2 matches the impedance of V2’s plate to the 8 
Ohm speaker. Negative feedback is provided by 
R23 feeding signal back to V1-B’s cathode. 

uDSP PCB  

The uDSP PCB is located in the back of the chassis 
opposite the power transformer. It provides the am-
plifier voicing and effects functions. The uDSP PCB 
is not field serviceable and must be replaced as an 
assembly. 

 
 

Summary of Contents for Super Champ-XD














Reviews: