11
EN
To move the machine while it is still inside the packing, use
a fork lift by inserting the two forks in the rooms provided
under the bearing board
Move the machine carefully and avoid sudden movements
which could unbalance the load and make it drop.
To remove the machine from the plate after packing
removal, loosen the fixing screws but keep them should
the machine be transported for long stretches.
To transport the machine after freeing it from the plate,
secure it with resistant chains, ropes or braces, by passing
them through the slits
A
provided in the basic tank.
Then the machine must be lifted using a hoist of adequate
capacity or through another means suitable for this purpose.
WARNING:
Do not lift the machine by the body D (Fig. 1).
WARNING:
Before lifting the machine, check that the body
is lowered and secured to the rest of the structure
by means of ropes or other claming means.
2.3
ELECTRICAL CONNECTIONS (Fig. 3)
Check that the mains to which the machine is connected is
earthed in accordance with current safety regulations and
that the power point is in good condition.
Connect a plug in compliance with safety rules to the end
of the mains cable of the machine, checking that the
yellow/green protective conductor is fitted into the relative
terminal marked.
(
ONLY FOR THREE-PHASE VERSION
: check for the
correct polarity of the motor through the blade which must
rotate
in the direction shown by the arrow
present on
the machine body. If this is not the case, invert two of the
three cables of the plug.
Mount electric panel
A
into its seat on the pivoting support,
and finally secure it by tightening the supplied fixing screws.
Remember that there should be a magnetothermic
protective device fitted upstream of the mains to protect
all the conductors from short circuits and overloads.
This protective device should be selected according to the
electrical features of the machine stated on the motor.
The motor of your sawing machine is equipped with a
protective heat circuit breaker which interrupts the power
supply when the temperature of the coils rises too high.
When the power supply is interrupted, wait for normal
reset.
SINGLE PHASE VERSION (Fig. 4)
In case of power failure in mains, while you wait for power
to be restored there is no danger hazard may arise : in fact,
the electronic speed variator is also equipped with a reset
function which prevents the machine from re-starting
automatically.
To start the machine, press the start push button
A
on the
handgrip twice.
THREE PHASE VERSION (Fig. 3-4)
In case of voltage failure in the system, you can wait for
the connection to be restored without danger of hazardous
conditions. In fact, the electric panel is equipped with a
reset function which prevents the machine from restarting
automatically.
To restart the machine, press the button
C (Fig. 4)
and
then push button
A
(Fig. 4) on the handgrip.
WARNING:
Never change the overload cutout setting to
avoid overloads which could damage the motor
circuits and other mechanical members.
Your sawing machine is equipped with a motor protection
obtained through a amperometric limiter which prevents
the motor from absorbing a current higher than the set
one, expressed by the maximum prescribed value of
absorption. If the limiter triggers while the machine is
operating, slightly diminish the cutting pressure. This enables
to safeguard the life and performance of the blade as well
as to always obtain a clean and precise cut.
2.4
POSITION/WORK STATION (Fig. 5)
Position the machine by moving it as described in paragraph
2.2 on to a sufficiently level bench, in such a way that the
coolant can reflow in the collecting tank during the cutting
operations.
Taking the ergonomic criteria into consideration, the ideal
height shall be that which enables you to position the table
between 90 and 95 centimetres from the floor
(see Fig.
2)
.
Now, cut the strap which holds the body lowered and
remove the wooden cap which protects the machine while
in transit.
CAUTION:
Read attentively the two labels on the handgrip
before starting any operation.
CAUTION:
Make sure that the machine is placed in a
working area with suitable environmental
conditions and lighting. The general conditions
of the working environment are of fundamental
importance for accident prevention.
Now lift the machine body and fit the eyelet of the
suspension tie rod
A
into its housing on the pin
B
, then
place the elastic ring
C
into the relative groove on the
same pin to stop the tie rod coming out.
