Fellowes Proteus A3/125 Technical & Service Manual Download Page 28

Page: 28 / 31

Revised 09 .15 .11

Proteus A3/125 Technical Service Manual

Remove/Replace Bridge Diode

Remove wire connector from Main PCB .

Remove screw from Bridge Diode .

Place new Bridge Diode and secure it with the screw .

Reattach the wire connector to Main PCB .

Remove/Replace Main PCB

Remove the 6 black connectors from the left side of the

Main PCB .

Remove the 5 white connectors from the right side of

the Main PCB .

Remove the cable from the Control Panel PCB .

Loosen the 2 screws on terminal block and remove

wires from the Bimetal Switch/Sensor Fixing Mat .

Remove the 4 screws that hold the Main PCB to the

Metal Bottom Plate .

Place new Main PCB and secure it with the 4 screws .

Reconnect the wires from the sensor and the connectors

to the right and left sides of the Main PCB .

DO THIS FIRST

Remove Housing Cover

TOOLS

Phillips screwdriver

DO THIS FIRST

Remove Housing Cover

TOOLS

Phillips screwdriver

Summary of Contents for Proteus A3/125
































Search results

Summary of Contents for Proteus A3/125

Reviews:

Related manuals for Proteus A3/125

Brands by name

Popular brands

Fellowes Proteus A3/125, Technical & Service Manual

Search results

Summary of Contents for Proteus A3/125

Reviews:

Related manuals for Proteus A3/125

Brands by name

Popular brands