7. Green Wait LED will fl ash and acoustic
bleep signal will sound when machine
is ready to laminate selected pouch
thickness.
4
5
ENGLISH
ENGLISH
ENG
WARRANTY
Fellowes warrants all parts of the laminator to be free of defects in material and workmanship for 2 years
from the date of purchase by the original consumer. If any part is found to be defective during the warranty
period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of
the defective part. This warranty does not apply in cases of abuse, mishandling or unauthorized repair. ANY
IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELLOWES BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ATTRIBUTABLE TO THIS PRODUCT. This warranty
gives you specifi c legal rights. You may have other legal rights that vary from this warranty. The duration,
terms and conditions of this warranty are valid world-wide, except where different limitations, restrictions or
conditions may be required by local law. For more details or to obtain services under this warranty, please
contact us or your dealer.
TROUBLESHOOTING
Problem
Ready Light does not go on after extended time
Pouch did not completely adhere to item
Jamming
Cause
Laminator is in a hot, humid area.
Laminated item may be too thick.
Pouch was not used.
Pouch was not centred or straight when fed
through Pouch/Document Entry.
g
Solution
Move laminator to a cool dry area.
Pass through laminator a second time.
All our laminators have been designed to operate jam-free.
In the unlikely event of a jam occurring, please press the red
g
p
g
p
release buttons on the sides of laminator, and wait for the
y
g p
p
y
g p
p
open light to turn on. (See image 1)
The laminator can be opened to remove incorrectly inserted
items as described under maintenance. Please ensure that
you follow the described steps. (See image 2)
Gently pull on the jammed material to release it. (See image 3)
Make sure that no residue is left on the rollers and use
cleaning sheet before laminating.
Always put item in a pouch.
Align sealed edge with Pouch/Document Entry. Use guide
to centre.
MAINTENANCE - Unique Easi-Access technology
MAINTENANCE - Unique Easi-Acc
h
E
A
h l
U i
E i A
h l
NCE U i
E i A
h l
MAINTENANCE - Unique Easi-Access technology
7. Please remember to re-secure them to
ensure safe operation.
1. To open the laminator, please press
the “Open” button as shown in the
illustration and wait for the “open”
LED to switch on and the ready beep.
2. Fans will turn on to cool the machine
down to safe handling temperature
inside.
3. The “open” LED will turn on and the
ready beep will sound when machine is
ready to be opened.
4. Press the red buttons on both sides of
the machine to activate the Easi-Access (The
laminator needs to be switched on to allow
the active temperature control to work).
6. For further maintenance, the rollers
can be released by experienced users.
Press cam levers to release the rollers.
HOT LAMINATION STEPS
1. Connect power cable to power
and to inlet at back of laminator.
2. Switch laminator on with
Power On / Off button at back
of machine
3. Press Stand-by button at left of front
operating panel to switch laminator on.
4. Use navigation keys to select setting
for the hot lamination pouch thickness
(3-7mil) you wish to laminate.
5. Press the round select key when the desired
thickness is indicated on the LEDs and wait for
the acoustic signal and the Ready Light next
to the selected pouch thickness.
6. Confi rm your selection by pressing
“Enter” button in the middle of navigation
keys. Laminator will take a few minutes
for temperature adjustment.
8. While laminator is warming up, please
prepare item you wish to laminate. Place the
item inside the pouch and centre it against
the sealed edge of the pouch. To prevent
jamming, use a carrier when item is smaller
than the pouch.
9. Place pouch, sealed edge fi rst, into
laminator entry. Keep pouch straight
and use the edge guide to centre it.
175
125
80
100
6
175
125
80
100
5
175
125
80
100
4
175
125
80
100
9
8
175
125
80
100
7
175
125
80
100
3
2
1
Need Help?
Please call our experts at
Customer Service. You’ll fi nd
the numbers for your nearest
Service Centre on the
BACK cover of this booklet.
175
125
80
100
1
175
125
80
100
3
175
125
80
100
7
175
125
80
100
6
4
17
5
12
5
80
10
0
3
175
125
80
100
2
1
This laminator is equipped with the unique Easi-Access technology for easy maintenance. This allows the user to open the laminator for maintenance, just like a photocopier.
i t i
i
d ith th
i
E i A
t h l
f
i t
Thi ll
5. Open the lid with both hands.
You are now able to clean the inside of
the laminator and carefully remove any
residual glue or other items.
When laminator is opened, power to
internal parts is isolated, so that user is
not in danger of electric shock.
17
5
12
5
80
10
0
5
10. To prevent jamming, immediately
remove laminated item from back of
machine. Let item cool on fl at surface for
several seconds.
11. Before switching off laminator, feed
empty cleaning/carrier sheet through
machine to clean unit.
175
125
80
100
11
175
125
80
100
10
0
2
Jupiter125_402104_3L_1112806.indSec4:4-Sec5:5 Sec4:4-Sec5:5
Jupiter125_402104_3L_1112806.indSec4:4-Sec5:5 Sec4:4-Sec5:5
11/28/06 10:30:33 AM
11/28/06 10:30:33 AM