4
Place the air purifier face up on a
flat, stable work surface. Open the
access panel by pressing in latches
POFBDITJEFPGUIFVOJU 'JH
%JTDPOOFDU NBJO IPVTJOH BTTFNCMZ
from rear housing assembly.
Separate main housing from rear
IPVTJOH-JGUNBJOIPVTJOHBTTFNCMZ
away from rear mounting housing
'JH
Open access panel and remove
filter assembly by pulling out on
top of side edges of frame, then
MJGUJOH /05& SFNPWF BMM QMBTUJD
XSBQGSPNGJMUFST 'JH
3FNPWFUIFTJYIPVTJOHTDSFXT 'JHBOETFUBTJEFGPSSFBTTFNCMZ
At the location of the two upper
IPVTJOHDPSOFSTDSFXT 'JHJOTFSU
a flat head screwdriver and gently
twist to release tab as shown in Fig
7. This will disconnect main housing
assembly from the rear housing
assembly.
MOUNTING REAR HOUSING AND MAIN ASSEMBLY
REAR HOUSING INSTALLATION & WIRING
Test the electrical outlet box first to ensure rated power requirements are met before beginning installation.
Remove air purifier from its shipping carton and remove all packing material.
Reference rear housing and locate desired mounting location. Again, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to
an existing stud.
Fig 3
Fig 7
Fig 4
Fig 8
Fig 5
Fig 6
Fig 10
Fig 11
Using provided template ensure electrical
PVUMFUCPYJTMPDBUFECFIJOEDBCMFIPMF "
JO 3FBS )PVTJOH BTTFNCMZ 'JH %SJMM
holes and place anchors in wall.
If mounting on concrete, cinder block or
brick type walls route the wires through
UIFiQVODIPVUwIPMFNBSLFE #JO'JH
Check for washers at all mounting
TDSFX MPDBUJPOT 'JH 1VMM XJSFT
from electrical outlet box through
hole in rear housing. Align housing
over anchors and securely install all
mounting screws.
"UUBDIXJSFTGSPNFMFDUSJDBMPVUMFUCPYUPXJSFTMPDBUFEJOTJEFSFBSIPVTJOHVTJOHXJSFOVUT.BUDIVQMJOF CMBDLBOEOFVUSBM XIJUFXJSFT 'JH.BLFTVSFBMM
connections are made in accordance with federal, state and local codes and regulations.
A
B
A
B
Fig 9
5
Make sure filters are in correct order
QSFGJMUFS DBSCPO GJMUFS )&1"
GJMUFSBOEJOTFSUFEJOUPGJMUFSGSBNF
'JH
IMPORTANT: Make sure filter
detection area aligns with window
JOGJMUFSGSBNF 'JH
Close front panel by pressing
firmly until both sides latch closed
'JH
5IF QPXFS DPOOFDUPS # JO 'JH
XJMM DBSSZ QPXFS GSPN UIF SFBS
housing to the main housing once
the assemblies are fully seated. The
main assembly will attach to the rear
housing assembly by the four screws
QSFWJPVTMZSFNPWFE 'JH5XP
TOBQIPPLT "JO'JHXJMMIPMEUIF
main and rear assemblies together
until the screws can be installed.
Carefully align the main assembly
with the rear housing assembly.
Slowly press into place until snap is
heard, and there is no gap between
UIF BTTFNCMJFT 'JH 5IF VOJU
should now support its own weight.
Open front panel by pressing
latches on both sides of unit. Allow
door to open fully. Insert filters
– IMPORTANT: make sure filter
detection window is aligned in
VQQFSSJHIUDPSOFS 'JH
To restrict access to the control panel
and filters the unit can be locked. To
lock, insert the key provided and
SPUBUFDMPDLXJTFUVSO 'JH
0ODF UIF VOJU JT DMPTFE SFFTUBCMJTI
QPXFS-JHIUTPOUIFDPOUSPMQBOFMXJMM
be visible through the lens, indicating
UIFVOJUJTPQFSBUJPOBM 'JH5IF
power light indicator will flash once
a second.
*OTUBMM TJY TDSFXT QSFWJPVTMZ SFNPWFE UP TFDVSF NBJO BTTFNCMZ UP SFBS
IPVTJOHBTTFNCMZ 'JH
RE-INSTALLING FILTERS
LOCKING ACCESS PANEL
MAIN ASSEMBLY INSTALLATION
WARNING:
To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before continuing any installation work.
IMPORTANT:
Make sure all plastic wrap is removed from filters.
Fig 16
Fig 17
Fig 18
Fig 19
Fig 20
Fig 21
Fig 14
Fig 12
Fig 13
Fig 15
1
2
3
4
5
6
1
2
3
4
5
6
A
A
B
