Fellowes 2T-LX-C36-24-BLK Assembly Instructions Manual Download Page 2

Page: 2 / 12

Page 2

TriumphLX

Components and tools

Please review these instructions before beginning the installation. Use the illustrations below to check that all components needed for your installation
were provided with your order. Do not discard the packaging until the product works to your satisfaction.

Components and tools

Additional tools required

• power drill with assorted drill bits

• Phillips screwdriver

• Phillips #1 and #2 bits

caution

• When drilling holes for the wood screws, guard against drilling through the

top of the worksurface.

• Always check that screws used to attach components to the worksurface

are not too long for the thickness of the surface.

work

surface

legs with

motor (2)

frame, C36 or C48 (1)

C48

C36

frame screws

digital keypad (1)

M3x20 #1 Phillips

round head (3)

motor cable (2)

5mm

Allen key (1)

M6x15

socket cap (8)

cord clips (10)

control unit (1)

M5x15 #2 Phillips

round head (2)

power cable (1)

feet (2)

M4.8x22 #2 Phillips

round head (12)

M3.5x16

#2 Phillips

flat head (10)

cam locks (2)

with cotter pin

Summary of Contents for 2T-LX-C36-24-BLK













Search results

Summary of Contents for 2T-LX-C36-24-BLK

Reviews:

Related manuals for 2T-LX-C36-24-BLK

Brands by name

Popular brands

Fellowes 2T-LX-C36-24-BLK, Assembly Instructions Manual

Search results

Summary of Contents for 2T-LX-C36-24-BLK

Reviews:

Related manuals for 2T-LX-C36-24-BLK

Brands by name

Popular brands