BASIC SHREDDING OPERATION
Continuous operation:
Up to 20-minutes maximum
NOTE:
Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
20-minutes will trigger
30-minute cool down period.
SafeSense
®
is active and
working properly
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
Touch test area and
look for the SafeSense
®
indicator to illuminate
Turn the shredder
ON ( ) to activate
SafeSense
®
SET-UP AND TESTING
1
3
ADVANCED PRODUCT FEATURES
Press ON ( ) to
activate (blue)
PAPER OR CARD
Feed paper/card
straight into paper
entry and release
Plug in and put
disconnect power
switch in ON (I) position
SilentShred
™
Technology
4JMFOU4ISFEOPJTFRVBMJUZ
shreds without noisy disruptions.
14
14
14
2
4
3
14
3
2
2
1
When finished
shredding set
to OFF ( )
4
Sleep Mode
Energy saving feature shuts down
automatically after 2 minutes of no
shredding activity.
SLEEP MODE OPERATION
Energy saving feature shuts down the shredder after
2 minutes of inactivity
WHEN IN SLEEP MODE
In sleep mode
To get out of sleep mode
touch control panel
insert paper
or
14
3
2
2
14
1
Press and hold forward ( )
2-3 seconds
2
PRODUCT MAINTENANCE
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
.
"MMNJDSPDVUTISFEEFSTSFRVJSFPJMGPSQFBLQFSGPSNBODF*GOPUPJMFEB
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
14
1
TO CLEAN THE SENSORS
1
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
Dip cotton swab in
rubbing alcohol
Using cotton swab, wipe
away any contamination
from the paper sensors
14
4
14
2
3
If hand is held on SafeSense
®
area more than 3 seconds,
shredder will shut off
For more information about all of Fellowes Advanced Product Features go to
www.fellowes.com
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain
illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and
recovery time for this shredder.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36053.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse (
BOESFNPWFQBQFS3FEVDFQBQFSRVBOUJUZUPBOBDDFQUBCMFBNPVOUBOESFGFFEJOUPQBQFSFOUSZ
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
TROUBLESHOOTING
SafeSense
®
Technology
Stops shredding immediately when
hands touch the paper entry.
