manualshive.com logo in svg

Felix Instruments F-900, Operation Manual

Share
Download
Felix Instruments F-900 Operation Manual Download Page 44

F-900 Instruction Manual rev. 1/16/2014 

 

1554 NE 3

rd

 Ave, Camas, WA 98607, USA                      Phone (360) 833-8835  Fax (360) 833-1914  

[email protected]                                                           http://www.felixinstruments.com

 

40

 

 

 

 

View Voltage 

The View Voltage screen shows the current voltage of the instrument.  Press the RIGHT arrow when 
Voltage is highlighted to check the unit’s voltage.  If any of these numbers are rapidly changing after 
the instrument has warmed up, please contact technical support at 

[email protected]

.  

Press the LEFT arrow or STOP to exit back to the View Menu.   

Voltage is set for each individual unit before leaving the Felix Instruments factory and is board 
specific.  For default voltage values, please see the Production Test Check Sheet at the end of the 
Instruction Manual or contact 

[email protected]

 with the serial number for factory 

voltage settings.  V_System is the voltage of the control board.  The voltage for V_Charger should 
increase when you connect the USB charger.  V_3volt is the digital voltage from the CPU and the 
V_Analog is the converted analog voltage.   

 

 

 

 

View Battery 

The View Battery menu displays indicates on the top line if the unit’s Charging is On or Off, or if the 
unit is connected via USB cable to a computer.  Press the UP/DOWN arrow to change the display 
and see the more information about the battery.  The QBAT value shows the battery level in 
hexadecimal follow immediately by the battery level in percent.  VBAT shows the voltage of the 
battery and TBAT indicates if the temperature of the battery is ok.  The R0 shows the output status 
of the battery charger.  Press the LEFT arrow or STOP to exit to the View Menu.   

 

 
 

 
 

 
 

 
 

When the instrument is connected to the charger, the top line will indicated “Charge On.”  The QBAT 
hexadecimal number should be changing and the battery percent increasing.  Also, the voltage will 
begin to increase slowly and the R0 will switch to 1d.  

Charge              

   Off 

 
QBAT:    

a413   60% 

VBAT:    

3.840V 

TBAT:    

OK 

Charge:         

Off 

Board:   

v6 

View                          Voltages 

V_System     =     5.98v 
V_Charger    =    4.64v 
V_3volt         =    3.31v 
V_Analog      =    2.07v 

Summary of Contents for F-900




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands