background image

Step-by-Step Assembly:

[email protected]

Page 6

Condenser Assembly:

Rotate the coarse focus knob (1) to raise the stage to 

its highest position. 

Rotate the condenser lowering knob (2) to lower the 

condenser bracket.

Loosen the condenser lock screw (3).

Insert the condenser and tighten the lock screw.

Raise the condenser back to the highest position.

Objective Assembly:

Rotate the coarse focus knob (1) to lower the stage.

Install the objectives (2) into the nosepiece (3) from 

the lowest magnification to the highest in a 

clockwise direction from the rear.

When operating the microscope always start using 

the lowest objective (4x or 10x) to get the sample 

into focus before moving to a higher magnification.

Eyepiece Assembly:

Remove the cover from the eyetube (1).

Insert the eyepiece (2) into the eyetube.

When adjusting the diopter on the eyepiece, ensure 

the eyepiece is locked into the eyetube with the hex 

screw (3) to avoid having the eyepiece rotate in the 

eyetube.

Light Source Assembly:

Align the orientation pin (1) and the power pin (2) to 

the holder (3) and socket (4).

Push the light source into the arm smoothly and 

plug it in.

Whenever replacing the bulb, turn off the power and 

ensure the bulb holder is not warm.

Replace entire LED light source if LED bulb is burned 

out. See page 15 of this manual for instructions.

Summary of Contents for RB30

















Reviews: