7
en
Safety pushbutton:
In situations of danger, press the safety pushbutton to
switch the machine off.
Adjusting the grinding belt.
Briefly switch the belt grinder on.
Observe in which direction the grinding belt runs out.
Adjust the belt tracking on the belt until the grinding belt
runs centrally on the contact roller (
21
).
If the belt tracking can not be adjusted centrally, the par-
allelism of the GXR must be adjusted (figure 2+3):
Loosen the two nuts (
9
).
Readjust screws (
9
) using a 1/64 in Allen key. Briefly
switch to the belt grinder.
Tighten the two nuts (
9
) again.
Check the parallelism of the belt tracking. Repeat the pre-
vious steps if the result is not satisfactory.
NOTE: The guidance device for the contact roller of the
GXR is set parallel ex works. Adjustment is only neces-
sary when centric belt tracking is not achieved while set-
ting up the drive wheel.
Adjusting the center height.
The height of the contact roller is normally adjusted to
the pipe center. However, the adjustment can also be
changed:
Release clamping lever (
15
).
Adjust the contact roller to the desired height with lever
(
14
).
Tighten the clamping lever again.
Check the adjustment with a grinding test-run.
Working instructions.
Adjust the belt tracking.
Adjust the center height.
If required, use a length stop (accessories) to precisely
clamp the workpiece.
Position yourself aside the machine and pull the feed
lever (
12
) with your left hand.
Rotate crank (
17
) with your right hand to move the work
table laterally and wear off the grinding belt uniformly.
When doing this, the workpiece may not be moved
beyond the edge of the grinding belt.
Always work with uniform feed pressure.
Noise emission values.
Repair and customer service.
Before any work on the machine itself, pull the
mains plug.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
The current spare parts list of this machine can be found
on the Internet under www.fein.com.
Carry out the following maintenance regularly:
Daily maintenance
Empty the collection box. Separate and dispose of water
and metal dust.
Open cover (
19
) and side cover (
8
) and remove the metal
dust.
The metal dust must be sufficiently cooled and may only
be disposed of in suitable containers.
Mount cover (
19
) and side cover (
8
) again.
Cleaning the exterior of the machine with compressed
air.
If required, you can change the following parts yourself:
Grinding belt, contact roller (
21
), spark guard (
10
)
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your machine may include only a
part of the accessories described or shown in this instruc-
tion manual.
Environmental protection, disposal.
Packaging, worn out machines and accessories should be
sorted for environment-friendly recycling.
Idle
Sanding
A-weighted emission pressure
power level measured at the
workplace L
pA
(re 20 μPa),
in decibels
90.5
99
Measuring uncertainty K
pA
,
in decibels
4
4
Measured A-weighted sound
power level L
wA
(re 1 pW),
in decibels
101
108
Measuring uncertainty K
wA
,
in decibels
2.5
2.5
Operating conditions
Speed rpm, (/min)
3 000
3 000
Material
– Stainless steel
Dimension (in)
–
Pipe, diametrer
1 43/64
Grinding belt
–
GRIT by Fein
36R
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the cor-
responding product standard.
Idle
Sanding
