17
en
When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
Before any work on the machine itself, remove the bat-
tery from the power tool.
If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is switched
off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water.
Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Use only intact original FEIN batteries that are intended
for your power tool.
When working with and charging
incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one’s health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of the
power tool and the materials being sanded, empty the dust
collector/container in time, observe the material manufac-
turer’s working instructions, as well as the relevant regula-
tions in your country for the materials being worked.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Emission values for vibration
Operating Instructions.
Do not use accessories not specifically intended and
recommended for this power tool by FEIN.
The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
Possible overloading of the vibration damping with
especially heavy accessories!
When using the large round sanding plate
(No. 63806195210, Ø115 mm) or the cleaning kit for tile
joints (No. 63719011220), the damping system can be
subject to overload due to the heavy weight of the acces-
sories. This becomes apparent through unpleasant and
very intense vibration of the machine.
Corrective action: Reduce the speed of the machine to
electronic level 2.
Due to the then possibly reduced working progress, the
machine is only suitable to a limited extent for above
mentioned accessories.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
Changing the tool (AFMT12(SL)) (see page 5).
Screw the clamping bolt in to the stop.
Changing the tool (AFMT12Q(SL)) (see pages 6/7).
Do not switch the power tool on while the clamping
lever is open.
Otherwise there is danger of crushes
or contusions to the hand and fingers.
Do not actuate the clamping lever while the power
tool is running.
Otherwise there is danger of injury.
Vibration
Classification of FEIN application
tools according to vibration class
Weighted
acceleration*
VC0
< 2,5 m/s
2
VC1
< 5 m/s
2
VC2
< 7 m/s
2
VC3
< 10 m/s
2
VC4
< 15 m/s
2
VC5
> 15 m/s
2
K
a
1,5 m/s
2
* These values are based on a work cycle consisting of no-load
and full-load operation of the same duration.
For information on the vibration class assigned to the application
tool, please see the enclosed data sheet 3 41 30 443 06 0.
OBJ_BUCH-0000000247-001.book Page 17 Thursday, January 28, 2016 2:33 PM
