background image

TST

 

Assembly instructions

 

 

FUZ2 -A/-B/-C/-CX/-L 

 

FEIG ELECTRONIC GmbH

 

Page 51 of 71

 

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

 

12  Messages 

12.1  Error messages 

Faults can be acknowledged provided they are not reset automatically. 

 

ATTENTION

 

The cause of the fault must be resolved first before the corresponding message is acknowledged.

 

Alternatively the 

 the STOP button can also be kept pressed for approx. 5 seconds. 

 

No. 

Description 

Possible reason for error 

F.000 

Door position too far up 

• Too small a parameter value for upper emergency limit switch → increase P.239 
• Upper limit switch range (limit switch band) too small → increase P.233 
• Mechanical brake defective or improperly set 

F.005 

Outside door position too far down 

• Too small a parameter value for lower emergency limit switch → increase P. 229 
• Lower limit switch range (limit switch band) too small → increase P. 223 
• Mechanical brake defective or improperly set 

F.020 

Run time exceeded (during 
opening, closing or deadman) 

• current motor run time has exceeded set maximum run time (P.410 (Opening), P.415 (Closing), P.419 
(Deadman move)), door may be sticking or is blocked. 
• Door is blocked 
• If using mechanical limit switches, one may not have tripped 

F.021 

Emergency opening wrong testing 

• The max. allowed run time (P.490) during testing has exceeded 
• Call service hotline 

F.030 

Lag error (position change of the 
door is less than expected) 

• door or motor is blocked 
• insufficient power for providing necessary torque 
• too little speed 
• mechanical limit switch was not left or is defective 
• Incremental or absolute encoder shaft is slipping 
• wrong positioning system selected (P.205) 
• one motor phase is missing 
• the brake does not release 
• Settings of the failure detecting time are not correct (P.430 or P.450) 

F.031 

Detected rotational direction 
deviates from expected 

• When using incremental encoders: Channel A and B reversed 
• Motor rotation direction reversed compared with calibration setting → teach in the limits new (P.210 = 5) 
• Too much „pancaking“ when starting, brake releases too soon, or too little torque, adjust boost (P.140 or P.145) 
as necessary. 

F.033 

Bad position transmitter protocol 

• Fault on the position transmitter 
• No position data available over an extended period 
 

Summary of Contents for TST FUZ2-A








































































Reviews: