Feig Electronic TST FUZ2-A Assembly Instructions Manual Download Page 45 | Manualshive

Page: 45 / 71

background image

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 43 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

9

Startup…

WARNING

Before starting the controller, check the electrical connections and the correct installation of the
plug-in cards. After start up, the operation of all the safety devices must be checked.

The settings are performed in dead man mode, i.e. press and hold the corresponding arrow key in
the corresponding direction until the desired position is reached.

9.1

…with absolute encoder or incremental encoder

1.

Open CALIBRATE mode by briefly pressing the

STOP key.

!Calibration!

0 Start with

"CALI:

2.

Move the door to the CLOSE position with the membrane keypad

CLOSE and

save by pressing the

STOP key for approx. 3 seconds.

If the door moves in the incorrect direction: incorrect motor
rotary field, turn off controller and reverse the 2 motor
connections. If the door does not move, the motor lacks
power. With the aid of the boost (performance increase at low
speeds) the motor can be supplied with an increase in power.
(see Chapter 9.5), if necessary, if necessary, check that the
brake was released.

Zur Zupos.

à

0 Übern. mit

E



i



E



u



4.

Move the door to the OPEN position by pressing the

OPEN

key and press the

STOP key for approx. 3 seconds.

To Open Pos.

à

xxx Übern. mit

E



i



E



o



If the door does not move, the motor lacks power. With the aid
of the boost (performance increase at low speeds) the motor
can be supplied with an increase in power. (see Chapter 9.5), if
necessary, if necessary, check that the brake was released.

The pre-limit switches and ramps are automatically adjusted by the subsequent travel of the door in
automatic mode.

Open Limit Set

~



Eo~

6.

press

briefly, the door moves down and is now taught in its

position.

Tor schließt
I.555 Lern Fahrt

I.5

55

Zu pos. OK

_



E

u_

7.

Now press

, repeat the process until the correction travel has

been completed. (Message I.510 = OK)

Door opens.
I.515 Correc. Fahrt

I.5

15

I.510 Korrek. OK

I.5

10

Tor öffnet

@OP

E

Tor schließt

2



U

F@

v Nemš

č

ini EICH

«
...
43
44
45
46
47
...
»

Summary of Contents for TST FUZ2-A








































































Reviews:

No comments

Related manuals for TST FUZ2-A

Brand: CALEFFI Pages: 2

Brand: CALEFFI Pages: 12

Brand: Caliber Pages: 6

Brand: FAAC Pages: 32

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: K1EL Pages: 46

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Rabe Pages: 61

Brand: Racal Instruments Pages: 35

Brand: RAKwireless Pages: 6

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands