background image

5

Installation Instructions

Model 350WBX Vibratone

®

 Horn

Safety Messages to Installers

The installation, maintenance, and disposal of this product must be 

carried out in accordance with national codes and standards.
It is important to follow all instructions shipped with this product. 

This device is to be installed by a trained electrician who is 

thoroughly familiar with and will follow all applicable national 

and local codes in the country of use.
The selection of the mounting location for the device, its controls 

and the routing of the wiring is to be accomplished under the 

direction of the Facilities Engineer and the Safety Engineer. In 

addition, listed below are some other important safety instructions 

and precautions you should follow:
•  Read and understand all instructions before installing or 

operating this equipment.

•  Do not connect this unit to the system when power is on.
•  Optimum sound distribution will be severely reduced if any 

objects are in front of the speaker. You should ensure that the 

front of the speaker is clear of any obstructions.

•  All effective warning horns produce loud sounds which may 

cause, in certain situations, permanent hearing loss. The device 

should be installed far enough away from potential listeners to 

limit their exposure while still maintaining its effectiveness. 

National Noise Standards, such as The OSHA Code of Federal 

Regulations 1910.95 in the United States, provide guidelines 

which may be used regarding permissible noise exposure levels.

•  After installation, ensure that all mounting screws are 

tightened.

•  Establish a procedure to routinely check the sound system for 

proper activation and operation.

•  Provide a copy of these instructions to the Safety Engineer, 

operator(s) and maintenance personnel.

Summary of Contents for Vibratone 350WBX











Reviews: