background image

Safety Messages for Installers and Operators

7

Installation and Maintenance Manual 

Federal Signal 

www.fedsig.com

•  When drilling into a vehicle structure, be sure that both sides of the surface are 

clear of anything that could be damaged. All drilled holes should be deburred 

and all sharp edges should be smoothed. All wires going through drilled holes 

should be protected by a grommet or convolute/split-loom tubing. Additionally, 

all exterior drilled holes must be sealed with Motorcraft seam sealer T-A-2-B 

or equivalent to prevent the potential exposure to carbon monoxide or other 

potentially harmful fumes. Failure to observe this warning could cause serious 

injury or death.

After Installation

•  After installation, test the siren and light system to ensure that it is operating 

properly.

•  Test all vehicle functions, including horn operation, vehicle safety functions and 

vehicle light systems, to ensure proper operation. Ensure that installation has 

not affected vehicle operation or changed any vehicle safety function or circuit.

•  After testing is complete, provide a copy of these instructions to the 

instructional staff and all operating personnel.

•  File these instructions in a safe place and refer to them when maintaining or 

reinstalling the product.

Failure to follow all safety precautions and instructions may result in property 

damage, serious injury, or death.

RETAIN AND REFER TO THESE MESSAGES

Safety Messages to Operators of Sound/Light Systems

People’s lives depend on your safe operation of Federal Signal products. It is 

important to read and follow all instructions shipped with the products. Listed 

below are some other important safety instructions and precautions you should 

follow:

•  Do not attempt to activate or deactivate the light system control while driving in 

a hazardous situation.

•  Although your warning system is operating properly, it may not be completely 

effective. People may not see or heed your warning signal. You must recognize 

this fact and continue to drive cautiously.

•  Situations may occur that obstruct your warning signal when natural and man-

made objects are between your vehicle and others, such as raising your hood 

or trunk lid. If these situations occur, be especially careful.

•  All effective sirens and horns produce loud sounds that may cause, in certain 

situations, permanent hearing loss. You and your passengers should consider 

taking appropriate safety precautions, such as wearing hearing protection.

Summary of Contents for Pathfinder Siren Series





















Reviews: