Federal Signal Corporation Informer15 I-IP15 Description, Specifications, Installation, Operation, And Service Manual Download Page 5

5

Safety Messages

Description, Specifications, Installation, Operation, and Service Manual

 

Federal Signal

 www.fedsig.com

Safety Messages

It is important to follow all instructions shipped with this product. This device is to be 

installed by trained personnel who are thoroughly familiar with the country’s electric 

codes and will follow these guidelines as well as local codes and ordinances, including 

any state or local noise-control ordinances.
Planning

•  If suitable warning equipment is not selected, the installation site for the Informer15 

Speaker is not selected properly, or the Informer15 Speaker is not installed properly, it 

may not produce the intended optimum audible warning. Follow Federal Emergency 

Management Agency (FEMA) recommendations. 

•  If Informer15 Speakers are not activated in a timely manner when an emergency 

condition exists, they cannot provide the intended audible warning. It is imperative 

that knowledgeable people, who are provided with the necessary information, be 

available at all times to authorize activation. 

•  When Informer15 Speakers are used out of doors, people indoors may not be able to 

hear the warning signals. Separate warning devices or procedures may be needed to 

effectively warn people indoors. 

•  The sound output of sirens is capable of causing permanent hearing damage. To 

prevent excessive exposure, carefully plan siren placement, post warnings, and 

restrict access to areas near sirens. Review and comply with any local or state noise 

control ordinances as well as OSHA noise exposure regulations and guidelines.

•  Activating the Informer15 Speaker may not result in people taking the desired actions 

if those to be warned are not properly trained about the meaning of warning sounds. 

Users should follow FEMA recommendations and instruct those to be warned of 

corrective actions to be taken.

After installation, service, or maintenance, test the system to confirm that it is operating 

properly. Test the system regularly to confirm that it will be operational in an emergency. 

Safety Messages to Installers

People’s lives depend on the safe installation of our products. It is important to follow 

all instructions shipped with this product. This device is to be installed by a trained 

electrician who is thoroughly familiar with the National Electrical Code and/or Canadian 

Electrical Code and will follow the NEC and/or CEC Guidelines as well as all local codes. 

This Informer15 Speaker should be considered a part of the warning system and not the 

entire warning system. 
The selection of the mounting location for this Informer15 Speaker, its controls and the 

routing of the wiring is to be accomplished under the Facilities Engineer and the Safety 

Engineer direction. Listed below are some other important safety instructions and 

precautions you should follow:
•  Electrocution or severe personal injury can occur when performing various 

installation and service functions such as making electrical connections, drilling 

holes, or lifting equipment. Therefore, only experienced electricians should install this 

Summary of Contents for Informer15 I-IP15





















Reviews: