Federal Signal Corporation Informer100 Speaker Manual Download Page 52

Page: 52 / 60

Appendix A Standard DV Messages

Informer100 Speaker (Models IS-I-IP100ACX and IS-I-IP100DCX)

Federal Signal

www.fedsig.com

FWS Name

Customer Name for
DV

Description

Notes

FWS-13985 TM31

(5 sec) Multi-Tone-Extremely Rapid Siren-
Multiple Frequency

FWS-13986 TM32

(5 sec) Caution-Extremely Rapid Siren-Multiple
Frequency

FWS-13987 Three 1 kHz tones

Pre-Announcement

Three 1 kHz tones Pre-Announcement

FWS-13988 Wobbulator-3 times

Pre-An- nouncement

Wobbulator-3 times Pre-Announcement

FWS-13989 FWS-10274-DSP2

M1 - Chime -
Pre-Announcement

DSP2 M1 - Chime - Pre-Announcement

FWS-13990 3 blasts-5 sec- Pre-

Announcement

3 blasts-5 sec- Pre-Announcement

FWS-13991 TM4-3 times Pre-

Announcement

TM4-3 times Pre-Announcement

FWS-13992 M15-3 times Pre-

Announcement

M15-3 times Pre-Announcement

FWS-13993 52 horn 5 sec

52 horn 5 sec

FWS-13994 52 horn 10 sec

52 horn 10 sec

FWS-13995 52 horn 15 sec

52 horn 15 sec

FWS-13996 52 horn 1 sec pulses

10 times

52 horn 1 sec pulses 10 times

FWS-13997 1 kHz_30 sec

1 kHz_30 sec

FWS-13998 (5 sec) Alt Steady

(5 sec) Alt Steady

FWS-13999 (5 sec) Alt Wail

(5 sec) Alt Wail

FWS-14000 (5 sec) Pulsed

Steady

(5 sec) Pulsed Steady

FWS-14001 (5 sec) Pulsed Wail

(5 sec) Pulsed Wail

FWS-14002 (5 sec) Steady

(5 sec) Steady

FWS-14003 (5 sec) Wail

(5 sec) Wail

FWS-14004 Westminster Chime

Westminster Chime

FWS-14005 Attention

Attention

Severe Weather

FWS-14006 Severe Weather

Warning-Seek
Shelter

“The National Weather Service has issued
a severe weather warning. Take shelter
immediately. Repeat, the National Weather
Service has issued a severe weather warning.
Take shelter immediately.”

FWS-14007 Severe Weather

Warning-Seek
Shelter

“This is a severe weather warning. Take shelter
immediately. Repeat, severe weather warning.
Take shelter immediately.”

FWS-14008 Severe Weather

Alert-Seek Shelter

“Please take shelter immediately. This is a severe
weather alert.”

FWS-14009 Severe weather

Approaching-Seek
Shelter

“Attention. Attention. This is an emergency.
Severe weather approaching. Seek shelter
immediately.”

FWS-14010 Severe Weather-

Stay away from
Windows

“Attention. A severe weather warning has been
issued; proceed immediately to the interior of the
building, away from windows and entrances.”

Summary of Contents for Informer100 Speaker





























































Search results

Summary of Contents for Informer100 Speaker

Reviews:

Brands by name

Popular brands

Federal Signal Corporation Informer100 Speaker, Manual

Search results

Summary of Contents for Informer100 Speaker

Reviews:

Brands by name

Popular brands