background image

2

   

Model FHLP-TAH Headlight Flasher

NOTE:

 When used in dark conditions, the low-beam headlights must be ON for proper illumination, while 

the high-beam headlights flash to gain attention and increase the vehicle’s visibility.

Table 1

  Product specifications

Operational Voltage:

9 Vdc to 16 Vdc

Standby Current:

Less than 10 mA

Flash Pattern:

PowerPulse™: Fast double flash alternating at 3.0 FPS, 
180 cycles/minute

Dimensions:

4.7 in L x 2.05 in W x 0.7 in H
(11.9 cm L x 5.2 cm W x 1.8 cm)

Material:

ABS plastic housing

Mounting:

Mounts on 4-inch centers

Wire Length:

8 in (20.3 cm)

Installing the Flasher

IMPORTANT:

 Do not use the Model FHLP-TAH on 2006 and older vehicles. 

The Model FHLP-TAH Headlight Flasher is designed to be water resistant. However, to ensure years of 
trouble-free operation, it should be mounted in a location that is protected from direct water spray and high 

temperatures. 

✔ 

Mounting hardware

✔ 

Activation switch for the 6J3 or 6J7 option

To mount and wire the flasher:

1. 

  Select a mounting location on the sheet metal below the passenger-side front head lamps and forward 

of the passenger-side front head lamp. DO NOT mount the flasher directly on the engine or close to 
the exhaust system.

2.

  Use the flasher as a template to mark the center of the two mounting holes. 

DRILLING PRECAUTION—When drilling holes, check the area into which 
you are drilling to be sure you do not damage vehicle components while 
drilling. All drilled holes should be de-burred and all holes should be 
smooth. All wire routing going through drilled holes should be protected 
by a grommet or convolute/split loom tubing.

3.

  Drill the two holes and use the installer-supplied mounting hardware to mount the flasher. 

4.

   In the front passenger-side wheel well, disconnect the harness plugs to the forward lamp. Connect the 

plugs to their matching plugs on the flasher.

5.

  For the 6J3 or 6J7 option, locate the GREEN/RED activation wire under the dash between the foot 

wells. Connect one terminal of the wire to one terminal of the installer-supplied activation switch.

6.

  Connect the other terminal of the activation switch to a source of +12 Vdc power.

Summary of Contents for FHLP-TAH









Reviews: