Federal Signal Corporation AM50 Installation Instructions Manual Download Page 3

INSTALLATION INSTRUCTIONS FOR MODEL AM50 ADJUSTABLE

POWER LOUDSPEAKERS

Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death to you or others.

 SAFETY MESSAGE TO INSTALLERS

Peoples lives depend on your safe installation of our products. It is important to follow

all instructions shipped with the products. This device is to be installed by a trained
electrician who is thoroughly familiar with the National Electric Code and will follow the
NEC guidelines as well as local codes.

The selection of the mounting location for the device, its controls and routing of the

wiring is to be accomplished under the direction of the Facilities Engineer and the Safety
Engineer. In addition, listed below are some other important safety instructions and
precautions you should follow:

This unit should be installed by a qualified electrician in accordance with
NFPA 72, and national and local Electrical and Fire Codes, under the
direction of the authority having jurisdiction.

If the unit is not installed in a supervisory system, it must be tested at
regular intervals. Refer to NFPA 72 and the local Fire Codes for this
information.

Read and understand all instructions before installing or operating this
equipment.

Do not connect this unit to the system when power is on.

All effective warning speakers produce loud sounds which may cause, in
certain situations, permanent hearing loss. You should take appropriate
precautions such as wearing hearing protection.

After installation, test the sound system to ensure proper operation.

All effective warning speakers produce loud sounds, which may cause, in
certain situations, permanent hearing loss. The device should be installed far
enough away from potential listeners to limit their exposure while still
maintaining its effectiveness. The OSHA Code of Federal Regulations 1910.95
Noise Standard provides guidelines which may be used regarding permissible
noise exposure levels.

Show these instructions to your Safety Engineer and then file them in a safe
place and refer to them when maintaining and/or reinstalling the unit.

Establish a procedure to routinely check the sound system for proper
activation and operation.

Consult the authority having jurisdiction in your area regarding the proper
use and installation of this product.

A.

GENERAL.

Model AM50 loudspeakers are Underwriters Laboratories listed for “Fire Protective

Signaling Use” (category designation UUMW). The loudspeakers are designed to reproduce
electronically generated warning tones that command rapid recognition of emergency

-1-

Summary of Contents for AM50





















Reviews: