manualshive.com logo in svg

FEDCO MSD-350, Installation & Operation Manual, Page: 41 / 66

Share
Download
FEDCO MSD-350 Installation & Operation Manual Download Page 41

MSD

TM

 Series

© Copyright 2018 Fluid Equipment Development Company | www.fedco-usa.com

- 

41

 -

Pump Assembly Continued

“REMOVE BEFORE

OPERATION”

Figure 75 - Seperating Coupling Hubs

2. 

Separate the motor hub from the dropout 

hub.

Figure 74 - 

Alignment Bushing Removal

Final Pump Alignment - No Motor Adapter

NOTES: 

Motor and pump to be installed on 

baseplate and 

Initial Pump Alignment

 proce-

dure completed.

NOTES: 

The following steps outline the dial 

indicator method. If using the 

Reverse Indica

-

tor 

or a 

Laser Alignment Tool Method

, retain 

alignment bushing until indication has been 

completed.

NOTES: 

Account for indicator sag. Angularity 

determined by coupling manufacturer. Contact 

FEDCO or see 

Sag Test 

section for additional 

information.
1. 

If present, remove alignment bushing and 

retain for future alignment purposes.

16. Install coupling guards and secure screws.

Figure 73 - 

Coupling Guard Installation

Summary of Contents for MSD-350



































































Reviews:

No comments