FeatureComforts MD100TBE Installation & Operation Instructions Download Page 9

9

 WARNING

: If the area in which the heater may be operated is smaller than that defined as 

     an unconfined space or if the building is of unusually tight construction, provide adequate  

     combustion and ventilation air by one of the methods described in the National Fuel Gas   

     Code, ANS Z223.1, Section 5.3 or applicable local codes.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or duct. You must provide two 

 

permanent openings: one within 12 inches 

of the ceiling and one within 12 inches of 

the floor. Connect these items directly to the 

outdoors or spaces open to the outdoors. 

These spaces include attics and crawl 

spaces. Follow the National Fuel Gas Code 

NFPA 54/ANS Z223.1. Air for Combustion 

and Ventilation for required size

of ventilation grills or ducts.

Ventilation Air From Inside Building

This fresh air would come from adjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must

provide two permanent openings: one

within 12 inches of the wall connecting

the two spaces (see options 1 and 2,

Fig. 1). You can also remove door into

adjoining room (see option 3, Fig. 1). 

Follow the National Fuel Gas Code 

 

NFPA 54/ANS Z223.1. Air for Combustion 

and Ventilation for required size of 

 

ventilation grills or ducts.

IMPORTANT

: Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlled power vent. Heated

air entering the attic will activate the

power vent. Rework worksheet, adding the

space of the adjoining unconfined space. 

The combined spaces must have enough 

fresh air to supply all appliances in both 

spaces.

Fig. 1 - Ventilation Air from 

Inside Building

Fig. 2 - Ventilation Air from 

Outdoors

 WARNING

: If the area in which the heater may be operated does not meet the required

     volume for indoor combustion air, combustion and ventilation air shall be provided by one

     of the methods described in the NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, the

     INTERNATIONAL FUEL GAS CODE, or applicable local codes.

Ventilation

Grills

Into Adjoining

Room, 

Option 1

Or

Remove

Door

Into

Adjoining

Room,

Option 3

Ventilation Grills

Into adjoining Room,

Option 2

12 in.

12 in.

Outlet 

Air

Ventilated 

Attic

To Attic

To Crawl 

Space

Outlet 

Air

Inlet 

Air

Inlet Air

Ventilated 

Crawl Space

Summary of Contents for MD100TBE































Reviews: