Fayat BOMAG BVP 10/36 Operating Instruction Download

Page: 72 / 112

8.2.2.2

Fuel stabilizer

If the machine is only occasionally used (if it is out of use for longer

than four weeks), mix in the correct amount of fuel stabilizer

directly after you have purchased fresh fuel.

The fuel stabilizer has a limited shelf life.

Please follow the instructions of the manufacturer concerning the

correct mixing ratio and shelf life.

Mixing in fuel stabilizer does not regenerate old fuel.

8.2.3 Oil for exciter shaft housing

Use only engine oils according to the following specifications:

API CI-4 or higher quality

Avoid mixing engine oils.

NOTICE!
Components may get damaged!

–

Do not use low-ash engine oils for the exciter

shaft housing.

Maintenance – Fuels and lubricants

BVP 10/36

Summary of Contents for BOMAG BVP 10/36

















































































































Search results

Summary of Contents for BOMAG BVP 10/36

Reviews:

Related manuals for BOMAG BVP 10/36

Brands by name

Popular brands

Fayat BOMAG BVP 10/36, Operating Instruction

Search results

Summary of Contents for BOMAG BVP 10/36

Reviews:

Related manuals for BOMAG BVP 10/36

Brands by name

Popular brands