background image

Rev 0.0

WARNINGS

EN

TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT 
THE DISHWASHER.

 

      

 DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED 
WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERI-
ALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION 
CENTRE. KEEP CHILDREN, PHYSICALLY AND/OR MENTALLY IMPAIRED 
ADULTS, AND ANIMALS AWAY FROM PACKAGING WASTE; DANGER OF 
SUFFOCATION.

BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS 
POWER SUPPLY FROM THE WORK AREA.

   

DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE 
SHARP EDGES OF THE APPLIANCE; WEAR SAFETY GLOVES. 

   

 THE APPLIANCE MUST BE PROVIDED WITH A GROUND CONNECTION IN 
ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE. 
IF IN DOUBT, HAVE THE SYSTEM CHECKED BY A QUALIFIED ELECTRI-
CIAN. 

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAM-
AGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE 
TO GROUND THE APPLIANCE OR FROM A DEFECTIVE GROUND 
CONNECTION.

   

DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRAN-
SIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE MUST BE IN-
STALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS 
PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN. 

   

 DO NOT OPERATE THE DISHWASHER UNLESS ALL THE OUTER PANELS 
HAVE BEEN POSITIONED CORRECTLY.
IMMEDIATELY AFTER INSTALLATION, BRIEFLY TEST THE APPLIANCE FOL-
LOWING THE INSTRUCTIONS INDICATED BELOW.  IF THE DISHWASHER 
FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL 
POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. 

DO NOT ATTEMPT TO REPAIR THE APPLIANCE.

   

  

 

Summary of Contents for F89088VI-M




































Reviews: