Faulhaber 3564K024BC series Instruction Manual Download | Manualshive

Page: 42 / 60

background image

42

Appendix

Electromagnetic Compatibility (EMC)

The sine wave commutated servomotor with
integrated motion controller (3564K024B C)
was tested and measured for EMC according
to the european guideline (89/336/EWG).

The System fulfills the following requirements
(norms) during operation at nominal values:

EMC emissions according to the range defined by
VDE 0839 part 81-2 (EN50081-2)

EMC immunity according to VDE 0839 part
82-2 (EN50082-2):

■

Electrostatic discharges of 4 kV
(through contact) and 8 kV (through air)
according to VDE 0847 part 4-2 (EN61000-4-2)

■

HF-fields according to VDE 0847 part 4-3
(EN61000-4-3)

■

Fast transients according to VDE 0847 part 4-4
(EN61000-4-4)

■

Cable bourne HF-currents according to VDE 0847
part 4-6 (EN61000-4-6)

The forementioned requirements are met when
the following conditions are fulfilled:

■

Operation according to the instruction
manual and given system data

■

The supply cables should be wound through
a ferrite tube, at least one winding, for
example, through a Kitagawa R1-16-28-7,
nearly to the controller

All components are grounded.

«
...
40
41
42
43
44
...
»

Summary of Contents for 3564K024BC series





























































Reviews:

No comments

Related manuals for 3564K024BC series

Brand: Waldbeck Pages: 72

Brand: Vimar Pages: 16

Brand: Toro Pages: 37

Brand: Chicago Pneumatic Pages: 100

Brand: DETROIT Pages: 84

Brand: Chicago Pneumatic Pages: 100

Brand: Honda Pages: 431

Brand: Steyer Motors Pages: 174

Brand: STEYR Pages: 118

Brand: Honda Pages: 42

Brand: Sachs Pages: 59

Brand: Hama Pages: 15

Brand: Vanguard Pages: 36

Brand: SANCH Pages: 139

Gast 16AM Series

Brand: Idex Pages: 8

Brand: Saito Pages: 22

Brand: Parker Pages: 8

HIMAX C 3528-0800

Brand: MULTIPLEX modell Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands