background image

FMT3006
Instruction Manual

Fast Mover Tools Limited

T: 01582 661993 F: 01582 667100 E: [email protected]

W: www.fastmovertoolsuk.com

Please look after the environment, dispose of all packaging in a responsible way.  
Always dispose of tools in accordance with local authority guidelines.

© 2012 Fast Mover Tools. This document is copyright and is not to be copied, circulated, distributed or shown to
anyone other than the intended recipient without the express permission of Fast Mover Tools.

Warranty

We hope that you will be very happy with your purchase.  If you do have a problem with your tool, you have the
added peace of mind of a 6 month warranty, which comes into date from the date of purchase (proof of purchase
required).

Scope of Warranty

- The warranty will cover you from all faults cause by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher specification.

What is not covered

- Normal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as Backing Pads, Airline Connections, Air  Fittings, Blades, 

Spanners, etc.

- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation, handling and 

storage of the product.

- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traced of water or rust inside tool - this shows that a properly working air filter has not been used.

Validity

- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;

- Tool is taken apart for any reason without our consent.
- Tool is not maintained daily.
- Air supply line is not used with a properly working air filter.

FMT3006_Product Instructions  18/06/2013  11:02  Page 8

Summary of Contents for FMT3006









Reviews: