INSTALLATION
Note: YPrPb output can only be used with the
720p and 540p output rates.
9.
IR receiver connection allows for use with
external IR receivers so unit can be installed
behind walls. (3.5mm, 3 pin, Tip = +5 - +12V
Pulse, Sleave = Gnd)
10.
12V trigger to activate automatic screen
relays. Voltage is constant when unit power is
on. (12V @ 100mA Max. 3.5mm 2 pin
connector, Tip = +12V, Sleave = Gnd)
11.
RS232 D9F connection for use with RS232
control systems. This connection also allows
for firmware upgrades.
12.
AC Power connection.
13.
RS232 Output - Not Active - for future upgrades
14.
Digital Audio Outputs (RCA, Coaxial,
AES/EBU). Be sure the audio processor is
compatible with the audio formats used.
These outputs are always active.
Note: The DVI or analog RGBHV outputs cannot be
active at the same time. Select the output type in the
Setup menu prior to use of the processor.
Connecting HDTV Satellite Receivers
Since HDTV ready satellite receivers offer different
signal types, they require special attention for
connection to the processor. Every receiver is
different so be sure to consult the receivers manual
for details. For this manual, we will assume the
receiver being used operates as follows:
1. Non HDTV material is output from the receiver
via an S-video connection
2. HDTV material is output via YPrPb outputs
3. If available, HDTV material is also output via a
DVI connector.
The following diagram offers one way to connect the system.
Note:
The pass-through input will “pass ” the input
signal to the output stage in the same format as the
input signal, i.e. analog HDTV in – analog HDTV out,
DVI HDTV in – DVI HDTV out.
HDTV Cross-Conversion
The DVP1510 can cross-convert 480p, 720p and
1080i HDTV signals to the selected output of the
processor. Any HDTV signal connected to the YPrPb
BNC or DVI inputs will be cross-converted. Any
HDTV or PC signal connected to the D15 input will be
passed-through without processing. PC signals via
the DVI input will be sent to the pass-through.
To pass-through HDTV signals to avoid processing,
select the passthrough input. The DVI input is
passed through to the DVI output. The analog YPrPb
input is passed through as analog RGB (when
transcode is selected).
HDCP Compatibility
The DVP1510 is a HDCP (High Definition Content
Protection) compatible processor. This means that
when used with a HDCP encrypted source (satellite
and DVD via DVI) and a HDCP compatible display
device, the digital signal can be processed and
viewed on the display device. If a non-HDCP source
is used, the image can also be viewed (Note: check
the display device manual to be sure this is possible
when using the DVI input). If a non-HDCP compatible
display is used, HDCP encrypted sources cannot be
viewed.
Note: When first selecting a HDTV source with
HDCP there can be an interruption of the video
image for up to 20 seconds while the HDTV source
unit communicates with the display device to verify
compatibility.
HDMI Connectors
To use sources or displays that use the HDMI
connector, simply use a HDMI to DVI converter cable
(Not supplied. See www.pacificable.com).
With this hookup viewing the different sources is as follows:
SOURCE
USE THIS
USE THIS
INPUT
OUTPUT
Non-HDTV
YPrPb or S-Video
DVI or RGBHV
HDTV Rates (480p,
720p,1080i) with
YPrPb or DVI
DVI or RGBHV
and without HDCP
Computer VESA
RGB
RGBHV or DVI
1024x768
(D15) or (DVI)
Pass-Through
DVP1510
S-Video
Input
YPrPb
Input
Display
RGBHV
DVI
S-Video
DVI
Satellite Receiver
YPrPb
HDTV
HD/PC
Input
DVI
Input
Alt.
Conn.
Set Pass-Through
input to Transcode
3
