FarmTek Growers Supply GrowSpan 104848 Manual Download | Manualshive

Page: 24 / 47

background image

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

24

Revision date: 06.20.18

END PANEL INSTALLATION (continued)

15. After installing all panels, cut and attach aluminum

profile to remaining upper edge of all polycarbonate

panels.

NOTE:

For rounded panel edges, prepare U-channel

profile as shown in photos that follow:

a. Cut angled notches from aluminum profile to allow

bending of the profile. Position notches closer for

tight curves.

Install profile here.

ATTENTION:

The U-channel profile (104213) for top

edge of all panels (dashed line below) is installed

last and after all profile is installed along edges and

between each panel.

b. Distance between notches is determined by degree

of bend required to fit rafter.

c. Bend U-channel at notches before installing it.

16. Standing outside the door, install Tek screws through

door frame and into end wall frame member to secure

the door.

17. Repeat procedure (as needed) to install remaining end

panels for other end of greenhouse.

NOTE:

Consult Quick Start section for additional

information.

18. Continue with

Main Cover Installation

procedures that

follow.

Tek screw

«
...
22
23
24
25
26
...
»

Summary of Contents for Growers Supply GrowSpan 104848
















































Reviews:

No comments

Related manuals for Growers Supply GrowSpan 104848

TITAN Peak 240 4,2

Brand: Dancover Pages: 16

Brand: GrowSpan Pages: 31

Brand: Westfalia Pages: 4

Brand: Palram Pages: 12

Brand: RUSTA Pages: 16

Rion Sun Lounge

Brand: Plasson Pages: 28

Brand: Simplicity Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands