background image

CANOPIES

8

Revision date: 10.13.15

INSTALL THE MAIN COVER

After assembling the main frame, install the main frame cover. 

Gather the parts:
•  Snugger ball tie downs (#CC4595)
•  Main cover and side panels (if equipped) 

NOTE

: Assistance is required to assemble the shelter.

1.  Locate the main cover, unfold it along the assembled frame, and pull it onto the frame and into position.

2.  Take the snugger ball tie downs, feed the stretch cord 

through a grommet, and attach the main cover to the 

assembled frame. See the above insert. Use one 

snugger ball for each grommet. 

3.  Once the main cover is installed, unfold the optional 

side covers (additional purchase required) along the 

frame and attach them to the main roof frame using the 

snugger balls. The dashed line in the diagram below 

shows where to attach the side cover.

4.  Read the Care and Maintenance section that follows.

 WARNING:

 To prevent property damage 

and personal injury, do not install the 

cover on a windy or stormy day.

NOTE:

 Dashed lines show 

where to attach the main cover 

to the frame.

NOTE:

 A space will remain between the cover edge 

and the frame as shown in the diagrams.

1

2

3

NOTE: 

Actual frame may 

differ from frame shown.

Summary of Contents for 1820SVSPC
















Reviews: