background image

5

CANOPIES

Revision date: 10.13.15

The following graphics and photos will help you identify the 

different parts and show you how they are used. 

 

(Some parts are not shown.)

CC4595  

Tie Down 8'' Snugger Ball

102193

3-Way Coupler

3-Way Coupler (includes lock bolt)

3-Way Coupler (no lock bolt)

102194

4-Way Coupler

There can be two types of couplers used during the assembly of the shelter: those that include an installed locking eyebolt 

and those that do not. See above. 

If the couplers included with your shelter do not have an installed lock bolt, u

se a self-tapping Tek screw

 to secure the 

different pipes to the couplers during the assembly process. The self-tapping Tek screws are included with the shipment.

 

 

ATTENTION:

 Tek screws are sent with all shelters of this type. For couplers with locking eyebolts, install the Tek screws at 

each pipe connection for additional security if desired.

 

 

WARNING:

 To prevent personal injury and damage to the shelter, 

fasten and tighten a Tek screw

 at each pipe and 

coupler joint. 

 

To prevent cover damage, install the Tek screw so that it 

does not

 touch the main cover or any optional side or end 

panels once these are installed.

ADDITIONAL PARTS IDENTIFICATION NOTES

In some instances, there can be differences between the parts that are shown and referenced in the instructions and 

the parts that are shipped with the shelter. These differences 

do not

 affect the integrity of the shelter, but can change the 

assembly procedures. 

The information that follows identifies possible changes in the assembly procedure found in this instruction document.

Please implement these changes during the assembly of the shelter.

Summary of Contents for 1820SVSPC
















Reviews: